2.
3.
Check adjustment per steps 4–6 of Install
Auger/Impeller Drive Control Linkage, page 9.
Make adjustments if required.
2.
3.
4.
5.
6.
7.
Drain gasoline from fuel tank. Refer to Draining
Gasoline, page 14.
Remove (2) screws holding belt cover in place
and set cover aside (Fig. 24).
Check tension of belt by operating the
auger/impeller. If belt still slips, replace the
belt. USE ONLY GENUINE TORO
REPLACEMENT PARTS.
Remove auger/impeller drive belt from engine
pulley and large auger/impeller pulley (Fig. 25).
Tip snowthrower forward and block it so it
cannot fall.
Replacing Auger/Impeller Drive
Belt
Remove (4) screws securing bottom cover to
frame (Fig. 20). Remove bottom cover.
Disconnect spring from notch in bottom edge of
side plate (Fig. 26).
When auger/impeller drive belt (Fig. 24) becomes
worn, stretched, oil–soaked or otherwise damaged,
belt replacement is required.
1.
2.
3.
4.
Pull wire off spark plug and make sure it does
not contact the plug accidentally.
POTENTIAL HAZARD
•
Spring is under heavy tension.
Remove (2) screws holding belt cover in place
and set cover aside (Fig. 24).
WHAT CAN HAPPEN
•
Spring could be thrown in operator’s or
bystander’s direction.
Remove auger/impeller drive belt from engine
pulley and large auger/impeller pulley (Fig. 25).
HOW TO AVOID THE HAZARD
•
Use caution when removing spring.
Install new belt around large auger/impeller
pulley (Fig. 25). Next, loop belt over engine
pulley, making sure that belt is on inside of idler
pulley and belt guide (Fig. 25).
8.
9.
Set unit upright and remove traction drive belt
from engine pulley and large traction pulley
(Fig. 25).
5.
6.
Adjust auger/impeller drive linkage. Refer to
steps 4–6 of Install Auger/Impeller Drive
Control Linkage, page 9.
Install new belt around large traction pulley.
Next, loop belt over engine pulley, making sure
that belt is on inside of belt guide (Fig. 25).
10.
11.
12.
Tip snowthrower forward and block it so it
cannot fall.
Reinstall belt cover with (2) screws.
Hook spring into notch in bottom edge of side
plate (Fig. 26).
Replacing Traction Drive Belt
Replace bottom cover with four screws and set
unit upright.
When traction drive belt becomes worn, stretched,
oil–soaked or otherwise defective, belt replacement is
required.
13. Reinstall auger/impeller drive belt around large
auger/impeller pulley and engine pulley, making
sure that belt is on inside of idler pulley and belt
guide (Fig. 25).
1.
Pull wire off spark plug and make sure it does
not contact the plug accidentally.
16
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38062, Toro 622, Toro 9900001 |
| Model Number | 38062 |
| Model Year | 1999 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 9900001 - 9999999 |
| Product Name | Toro 622 38062 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 7 oz. (198gm) Lubriplate MAG-1 |
| Engine Motor Model # | HSK60-76011C |
| Engine Motor Size | 6 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(3 votes, average: 4.67 out of 5)
Lawn and Garden readers have rated Toro 622 38062 Snow Blower Operators Manual, 1999 4.7 out of 5.0 based on 3 product reviews. Fine snowblower, no complaints
Thank you very Much!!!!!!
5