SERVICE AND ADJUSTMENTS
1.
2.
3.
Disengage all controls and move throttle control to
WARNING: To avoid serious injury,
before performing any service or ad-
justments:
STOP position. Wait for all moving parts to stop.
Disconnect spark plug wire from spark plug and place
it wear it cannot come in contact with spark plug.
1.
2.
3.
Be sure throttle is in STOP position.
Remove safety ignition key.
Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
Make sure the augers and all moving
parts have completely stopped.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts as supplied
with your snow thrower.
4.
Disconnect spark plug wire from
spark plug and place wire where it
cannot come in contact with plug.
4.
Connect spark plug wire to spark plug.
SNOW THROWER
TO ADJUST SNOW THROWER HEIGHT
1/4-20
LOCKNUT
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
See“TOADJUSTSKIDPLATES”and“SCRAPERBAR”in
the Operation section of this manual.
IMPELLER HUB
CHUTE DEFLECTOR
IMPELLER
SHAFT
The chute deflector, attached to the top of the discharge
chute,isprovidedtodirectdischargingsnowawayfromthe
operator. If the deflector becomes damaged, it should be
replaced.
WARNING: To avoid serious injury,
never operate your snow thrower with
the deflector removed or damaged.
•
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
AUGER
HUB
SHEAR BOLTS
1
/4-20
AUGER
HUB
AUGER
SHAFT
AUGER SHEAR BOLTS
LOCKNUT
Both right and left-hand augers are secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a
foreign object or ice become lodged in the augers, the
shear bolts are designed to break, preventing damage to
any other components. If one or both augers do not turn
when auger control lever is engaged, check to see if one or
both of the bolts have sheared. To replace the shear bolts:
TO REMOVE BELT COVER
1.
Remove the two (2) screws securing belt cover to
frame.
2. Remove belt cover.
1.
2.
3.
Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
•
Replace belt cover by installing cover and screws and
tighten securely.
Disconnect spark plug wire from spark plug and place
it wear it cannot come in contact with spark plug.
BELT
COVER
Align hole in auger hub with hole in auger shaft and
install a new 1/4-20 x 2" shoulder/shear bolt. Install
1/4-20
lock nut and tighten securely.
CAUTION: Do not substitute. Use only original
equipment shear bolts as supplied with your
snow thrower.
4.
Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)
capscrew/shearboltsandhexnuts.Shouldaforeignobject
or ice become lodged in the impeller, the capscrews are
designedtobreak,preventingdamagetoanyothercompo-
nents. If impeller does not turn when auger control lever is
engaged, check to see if the capscrews have sheared. To
replace the capscrew/shear bolts:
FRAME
SCREWS
16
| Categories | Husqvarna Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Husqvarna 9027ST |
| Model Year | 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Husqvarna, Snow Blower |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)