Installing the Chute Control
Gear
1.
Insert the one-inch (2.5 centimeters) carriage bolt into
the mounting hole of the gear bracket (Fig. 8).
5
1
171
1
Figure 9
4
1.
Scraper
2
170
3
3. Remove the two flange bolts and flat washers that
secure the ends of the scraper to the side plates
(Fig. 10).
Figure 8
1.
2.
Gear bracket
3.
4.
5.
Mounting flange
Chute gear rod
Worm gear
Carriage bolt, flat washer,
and locknut
1
2.
3.
Position the worm gear into the bracket, align the holes,
and insert the chute gear rod through the bracket and the
gear (Fig. 8).
5
4
Loosely mount the worm gear and the bracket to the
mounting flange with a carriage bolt, a flat washer, and
a locknut (Fig. 8).
2
3
m-4932
Figure 10
4.
5.
Slide the worm gear into the teeth of the chute gear and
tighten the locknut.
1.
2.
3.
Side plate (2)
Flange bolts (4)
Skid (2)
4.
5.
Flat washers (4)
Locknut (2)
Operate the chute control. If the chute control binds,
apply a light coat of grease to the worm gear and move
it slightly outward if it binds; move it slightly inward if
it is too loose.
4.
5.
Insert a flange bolt through the rear slot in each skid.
Insert a washer between each skid and the side plate
(Fig. 10). Do not tighten the bolts.
Installing the Skids
6.
7.
Install a flange bolt through the front slot of each skid
and the side plate.
1.
Check the air pressure in the tires; refer to Checking the
Tire Pressure on page 12.
Insert a washer and a locknut behind (on the inside of)
the side plate (Fig. 10). Do not tighten the bolts.
2.
Move the snowthrower to a flat surface and ensure that
the scraper (Fig. 9) is parallel to the ground. If it is not,
adjust the scraper; refer to Adjusting the Skids and the
Scraper on page 19.
Note: The following steps describe how to adjust the skids
for paved surfaces. For gravel or crushed rock surfaces,
refer to Adjusting the Skids and the Scraper on page 19.
8.
Manually move the wheels to the rear Power Shift
position by lifting up on the handgrips and moving the
shift control fully forward (Fig. 11).
10
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 1028 Power Shift, Toro 1332 Power Shift, Toro 38547, Toro 38560, Toro 38592, Toro 924 Power Shift |
| Model Number | 38547, 38560 and 38592 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 220000001 - 220999999 |
| Product Name | Toro 924 Power Shift Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Two Stage Power Shift |
| Swath | 24 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Engine Motor Model # | OHSK90-221413C |
| Engine Motor Size | 9 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 4 Forward/2 Reverse |
| Transmission Type | Gear |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)