•
Electric Starter (Fig. 18)—Push the starter button to
start the engine.
2
1
3
4
1
mĆ4947
Figure 20
1.
Green ground wire clip
m–4516
Figure 18
7.
8.
9.
Install the choke knob.
1.
2.
Electric starter
Starter button
3.
4.
Receptacle
Power cord
Insert the ignition key.
Connect the wire to the spark plug.
•
Power Cord (Fig. 18)—Connect the power cord to the
electric starter and to an electrical outlet when starting
the engine.
Important
choke and throttle positions.
Use the heater box as a reference for the
Removing the Carburetor
Heater Box
Installing the Carburetor
Heater Box
If40you_
F (4operate_C), removethe enginethe carburetorwhen the airheatertemperaturebox (Fig.is19).above
To install the carburetor heater box, reverse steps 1 through
9 of Removing the Carburetor Heater Box on page 14.
Remove the fasteners from their holes before installing the
carburetor heater box.
1
Starting the Engine
Important
Ensure that there are no obstructions in the
auger/impeller and the discharge chute before you operate
the snowthrower. Use a stick, not your hand, to remove an
obstruction from the auger/impeller or the discharge chute.
mĆ5006
1.
2.
Connect the wire to the spark plug.
Figure 19
Move the speed shift control to the N (Neutral) position
and the throttle to the Fast position.
1.
Carburetor heater box
3.
4.
Release the auger/impeller drive control lever and the
traction control lever (Fig. 13).
1.
Disconnect the wire from the spark plug and ensure that
the wire does not contact the plug (Fig. 19).
Open the fuel shutoff valve below the fuel tank
(Fig. 15).
2.
3.
4.
Remove the key from the ignition switch (Fig. 14).
Pull the choke knob off (Fig. 14).
5.
6.
Rotate the choke (Fig. 14) to the On position.
Remove two screws and the three bolts that secure the
carburetor heater box in place (Fig. 19).
Insert the ignition key (Fig. 14).
Important
engine has been running and is hot. Excessive priming may
flood the engine and prevent it from starting.
Do not use the primer or the choke if the
Note: Install these fasteners in their holes for safe
keeping.
5.
6.
Lift the carburetor heater box up and away from the
engine.
7.
Cover the hole in the center of the primer (Fig. 14) with
your thumb and slowly push in the primer three times,
pausing a moment between pushes.
Disconnect the green ground wire clip under the throttle
(Fig. 20).
8.
For the recoil starter:
14
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 1028 Power Shift, Toro 1332 Power Shift, Toro 38547, Toro 38560, Toro 38592, Toro 924 Power Shift |
| Model Number | 38547, 38560 and 38592 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 220000001 - 220999999 |
| Product Name | Toro 924 Power Shift Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Two Stage Power Shift |
| Swath | 24 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Engine Motor Model # | OHSK90-221413C |
| Engine Motor Size | 9 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 4 Forward/2 Reverse |
| Transmission Type | Gear |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)