MTD Troy-Bilt RZT Series 42 Inch Tractor Mower Deck Lawn Mower Owners Manual

Removing The Tractor From Storage
To adjust the drive control lever height, proceed as follows:
Check the engine oil.
Remove the flange lock nut, flat washer, and hex screw
securing the lever to the pivot bracket.
Fully charge the battery and inflate the tires to the
recommended pressure.
While supporting the control lever to keep it from
falling, remove the hex insert flange lock nut and
shoulder screw from the bottom of the control lever
and pivot bracket. Refer to Figure 6-5.
If drained before storing, fill the fuel tank with clean,
fresh gasoline.
Add clean, fresh fuel.
Reposition the control lever to align with the other set
of holes in the pivot bracket and insert the shoulder
screw removed earlier. Fasten with the hex insert flange
lock nut and tighten until snug.
Start the engine and allow to idle for a few minutes to
ensure engine is operating properly.
Drive the tractor without a load to make certain all the
tractor systems are functioning properly.
Insert the hex screw w/washer through the control
lever slot and the pivot bracket. Thread the flange lock
nut onto the screw, but do not tighten now.
Adjustments
WARNING! Shut the engine off, remove the
If you are going to adjust the control levers forward or
rearward, proceed to the next step. If not, fully tighten
the flange lock nut.
ignition key and engage the parking brake
before making adjustments. Protect your
hands by using heavy gloves when handling
the blades.
PivotBracket
ControlLever
Adjusting the Operators Seat
To adjust the position of the seat, move and hold the
seat adjustment lever toward the left. Slide the seat
forward or rearward to the desired position; then
release the adjustment lever. Make sure seat is locked
into position before operating the tractor. See Figure
6-4.
FlatWasher
Flange
LockNut
HexScrew
Height
Adjust
Holes
Seat
Shoulder
Screw
Figure 6-5
To adjust the drive control levers forward or rearward,
proceed as follows:
MoveLever
toLeft
If not already loose, loosen the flange lock nut and rotate
the control lever either forward or rearward to the desired
position. See Figure 6-5.
Adjustment
Lever
NOTE: If the control lever is too tight to move, slightly loosen
the hex insert flange lock nut and shoulder screw at the
bottom of the control lever.
Figure 6-4
Tighten the flange lock nut to fix the control lever in
the adjusted position
Adjusting RH & LH Drive Control Levers
Repeat the above procedure to adjust the other control
lever into the same position. Adjust so that both levers
are even with each other when in the neutral position.
The RH and LH drive control levers can be adjusted up or
down and fore-and-aft for the comfort of the operator. The
drive control levers can be placed in either of two height
positions, and/or can be moved forward or rearward
within the range of the slot in each control lever mounting
bracket.
sectiOn 6 — Maintenance & adjustMents
23
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 36 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website