HydroJect 3010 Specifications*
®
HYDROJECT 3010 POWER TRAIN SYSTEM
Kohler
®
CH740, 4-cycle, opposed twin, air cooled, 27 hp (20 kW) @ governed maximum 3600 rpm (gross). 44 cu. in. (725 cc)
ENGINE
displacement. Electric start. Solid state electronic ignition. Heavy-duty air cleaner. 2 quart (1.9 liter) oil reservoir.
10.5 gallon (39.7 liter) fuel capacity for over four hours of operation. Includes fuel shut off valve. Uses unleaded gasoline.
Three interchangeable, smooth tread tires; 18 x 9.50-8, 2-ply, pneumatic, tubeless tires with drop center demountable rims.
FUEL SYSTEM
TIRES/WHEELS
Hydrostatic variable volume pump and low speed, high torque, 24 cu. in/rev wheel motor. 5 quart (4.7 liter) reservoir and suction line
with 25 micron filter. Traction to propel unit is through single drive/steer tire at tiller. Traction pump driven by continuously engaged belt.
TRACTION DRIVE
TRACTION CONTROL
TRANSPORT LIFT
Traction control lever moves back and forth to control variable speed and traction direction.
12 volt linear screw actuator, 6" (15 cm) stroke; raises and lowers lift arm/transport tires and activates hole spacing.
Aerating speed: 0-2 mph (0-3.2 km/h)
(both directions). Transport speed (capable
only when up on all three tires): 0-4 mph
(0-6.4 km/h) (both directions).
Spacing in the Direction of Travel
inches (cm)
Productivity
(sq.ft./h) (sq.m./h)
GROUND SPEED &
SPACING
1.5" (3.8)
3.0" (7.6)
4.5" (11.4)
6.0" (15.2)
6,500 (604)
13,000 (1,208)
19,500 (1,812)
26,000 (2,415)
BRAKE
ELECTRICAL SYSTEM
FRAME
Drum and shoe type parking brake.
12 volt, Group 28 battery with 525 cold cranking amps. 20 amp charging system with circuit breaker protection. Solid state potted
electrical controller and sealed weather pack connections.
Formed and welded steel construction.
Engine panel: throttle, choke, key switch, hour meter, supply water pressure gauge, circuit breaker, roller wash control and spacing
control lever. Steering handle: bidirectional traction lever, aeration start and stop buttons, transport/aerate lift toggle switch, and parking
brake with buzzer.
CONTROLS/GAUGES
AERATE WIDTH
33" (83.3 cm); with 11 nozzles spaced every 3" (7.6 cm).
OVERALL DIMENSIONS
& WEIGHT (APPROX.)
Height
38.2" (97 cm)
Length
96" (245 cm)
Width
63" (160 cm)
Wheelbase
53" (135 cm)
Weight
1,120 lbs. (508 kg)
WATER INJECTION SYSTEM
Required water supply: 8 gpm @ 20-80 psi (30.3 liters/m @ 1.3-5.5 bars). A water pressure sensor disengages the water system if the
water supply at machine drops below 20 psi (1.3 bars). Supply water filter with replaceable 5 micron element;
P/N 86-8620. Quick connect water hose coupling for attaching to water hose supply.
WATER SUPPLY
Toro exclusive stainless steel head, 3 piston type with forged crank shaft, stainless push rods. Nominal performance is 4 gpm @ 5000
psi (15 liters/m @ 344.8 bars). Pump is driven by two belts electromagnetically engaged.
PUMP
ACCUMULATOR
CAM CASE
Water energy storage device; nitrogen gas charged to a maximum of 2500 psi (172.4 bars).
Cam actuates valve to release water to the manifold at 5.3 cycles per second (320 injection/m). Case also serves as a
4 quart (3.8 liters) oil reservoir. Cam gear electromagnetically engaged and driven through flexible coupling from engine.
Valve housing provides high pressure water passage area. Pressure balanced valve spool with hardened stainless seat. Bleed valve in
base allows bleed off of high pressure and drain down for cold weather storage. Bolted flanges and O-rings mate all components to
valve body.
VALVE
Pivoting aluminum rollers reduce compactive ground pressure and uniformly smooth the surface. Adjustable flow spray wash system
maintains clean rollers. Variable roller washing requires up to 4 gpm (15 liters/m) additional water flow.
ROLLERS
PRESSURE RELIEF VALVE
MANIFOLD/NOZZLES
Poppet type preset to 5000 psi (344.8 bars). Corrosion resistant stainless and brass materials.
Stainless steel nozzle bodies with check valves and hardened stainless steel discharge orifices. Check valves may be reversed in
housing to block unused nozzles. Optional sizes/diameters with staggered pattern available.
Drill Size
Nozzle Size
Inches
.0595
.0810
.0465
Nozzle Size
mm
1.511
2.057
1.181
Approximate
Depth**
4-6" (10-15 cm)
5-7" (13-18 cm)
3-4" (10-15 cm)
Maximum # of
Nozzles in Use
11
6 (must block 5 nozzles)
6 (use w/ five #46 nozzles)
NOZZLE SIZE &
DEPTH CHART
Standard
#53
#46
#56
**Depths beyond 20" (51 cm) can be obtained using additional shots. See Operator’s Manual for complete details.
Wetting Agent; (2) 2.5 gallon (9.5 liter) jugs, P/N 86-8530. 25 Micron Pre-filter and Filter Body, P/N 80-9590 and 80-8600. Injection
System (09830) allows metering of wetting agent into water supply. Lift Kit (09831) allows aeration to occur in the raised position.
OPTIONS
WARRANTY
Two year or 500 hour limited warranty; 120 days for contract or rental use. Refer to the Operator’s Manual for further details.
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual
products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.
The HydroJect 3000 is manufactured
in Tomah, WI ISO 9002 Certified Plant.
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Hydroject 3010 |
| Download File |
|
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)