HydroJect 3010 Specifications*
®
HYDROJECT 3010 POWER TRAIN SYSTEM
Kohler
®
CH740, 4-cycle, opposed twin, air cooled, 27 hp (20 kW) @ governed maximum 3600 rpm (gross) 44 cu in (725 cc)
FUEL SYSTEM
displacement Electric start Solid state electronic ignition Heavy-duty air cleaner 2 quart (1 9 liter) oil reservoir
10 5 gallon (39 7 liter) fuel capacity for over four hours of operation Includes fuel shut off valve Uses unleaded gasoline
Three interchangeable, smooth tread tires; 18 x 9 50-8, 2-ply, pneumatic, tubeless tires with drop center demountable rims
TIRES/WHEELS
TRACTION DRIVE
Hydrostatic variable volume pump and low speed, high torque, 24 cu in/rev wheel motor 5 quart (4 7 liter) reservoir and suction
line with 25 micron filter Traction to propel unit is through single drive/steer tire at tiller Traction pump driven by continuously
engaged belt
TRACTION CONTROL
TRANSPORT LIFT
GROUND SPEED &
Traction control lever moves back and forth to control variable speed and traction direction
12-volt linear screw actuator, 6" (15 cm) stroke; raises and lowers lift arm/transport tires and activates hole spacing
Aerating speed: 0-2 mph (0-3 2 km/h)
(both directions) Transport speed (capable
only when up on all three tires): 0-4 mph
(0-6 4 km/h) (both directions)
Spacing in the Direction of Travel
inches (cm)
1 5" (3 8)
3 0" (7 6)
4 5" (11 4)
Productivity
(sq.ft./h) (sq.m./h)
6,500 (604)
13,000 (1,208)
19,500 (1,812)
26,000 (2,415)
SPACING
6 0" (15 2)
BRAKE
ELECTRICAL SYSTEM
FRAME
Drum and shoe type parking brake
12-volt, Group 28 battery with 525 cold cranking amps 20 amp charging system with circuit breaker protection Solid state potted
electrical controller and sealed weather pack connections
Formed and welded steel construction
Engine panel: throttle, choke, key switch, hour meter, supply water pressure gauge, circuit breaker, roller wash control and spacing
control lever Steering handle: bidirectional traction lever, aeration start and stop buttons, transport/aerate lift toggle switch, and
parking brake with buzzer
CONTROLS/GAUGES
AERATE WIDTH
33" (83 3 cm); with 11 nozzles spaced every 3" (7 6 cm)
OVERALL DIMENSIONS &
WEIGHT (APPROx.)
Height
38 2" (97 cm)
Length
96" (245 cm)
Width
63" (160 cm)
Wheelbase
53" (135 cm)
Weight
1,120 lbs (508 kg)
WATER INJECTION SYSTEM
Required water supply: 8 gpm @ 20-80 psi (30 3 liters/m @ 1 3-5 5 bars) A water pressure sensor disengages the water system if
the water supply at machine drops below 20 psi (1 3 bars) Supply water filter with replaceable 5 micron element;
P/N 86-8620 Quick connect water hose coupling for attaching to water hose supply
WATER SUPPLY
Toro exclusive stainless steel head, 3 piston type with forged crank shaft, stainless push rods Nominal performance is 4 gpm @
5000 psi (15 liters/m @ 344 8 bars) Pump is driven by two belts electromagnetically engaged
PUMP
ACCUMULATOR
CAM CASE
Water energy storage device; nitrogen gas charged to a maximum of 2500 psi (172 4 bars)
Cam actuates valve to release water to the manifold at 5 3 cycles per second (320 injection/m) Case also serves as a
4 quart (3 8 liters) oil reservoir Cam gear electromagnetically engaged and driven through flexible coupling from engine
Valve housing provides high pressure water passage area Pressure balanced valve spool with hardened stainless seat Bleed valve
in base allows bleed off of high pressure and drain down for cold weather storage Bolted flanges and O-rings mate all components
to valve body
VALVE
Pivoting aluminum rollers reduce compactive ground pressure and uniformly smooth the surface Adjustable flow spray wash
system maintains clean rollers Variable roller washing requires up to 4 gpm (15 liters/m) additional water flow
ROLLERS
PRESSURE RELIEF VALVE
MANIFOLD/NOzzLES
Poppet type preset to 5000 psi (344 8 bars) Corrosion resistant stainless and brass materials
Stainless steel nozzle bodies with check valves and hardened stainless steel discharge orifices Check valves may be reversed in
housing to block unused nozzles Optional sizes/diameters with staggered pattern available
Drill Size
Nozzle Size
Inches
0595
0810
0465
Nozzle Size
mm
1 511
2 057
1 181
Approximate
Depth**
4"-6" (10-15 cm)
5"-7" (13-18 cm)
3"-4" (10-15 cm)
Maximum # of
Nozzles in Use
11
6 (must block 5 nozzles)
6 (use w/ five #46 nozzles)
NOzzLE SIzE &
DEPTH CHART
Standard
#53
#46
#56
**Depths
beyond 20" (51 cm) can be obtained using additional shots See Operator’s Manual for complete details
Wetting Agent; (2) 2 5 gallon (9 5 liter) jugs, P/N 86-8530 25 Micron Pre-filter and Filter Body, P/N 80-9590 and 80-8600 Injection
System (09830) allows metering of wetting agent into water supply Lift Kit (09831) allows aeration to occur in the raised position
OPTIONS
WARRANTY
Two-year or 500 hour limited warranty; 120 days for contract or rental use Refer to the Operator’s Manual for further details
*Specifications and design subject to change without notice Products depicted in this literature are for demonstration purposes only
Actual products offered for sale may vary in use, design, required attachments and safety features Consult your local Toro Distributor
The HydroJect 3010 is manufactured
in Tomah, WI ISO 9002 Certified Plant
102
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Hydroject 3010 |
| Download File |
|
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)