Husqvarna 10527SBE Snow Blower Owners Manual

OPERATION
TO ADJUST SKID PLATES (See Fig. 19)
When not  using drift cutters, loosen  adjustment nut,
lower to storage position and tighten nut securely.
NOTE:Thewrenchprovidedinyourpartsbagmaybeused
to adjust the skid plates.
BEFORE STARTING THE ENGINE
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
ground surface. Adjust skid plates evenly to proper height
for  current surface  conditions.  For  removal of  snow  in
normal conditions, such as a paved driveway or sidewalk,
place skid  plates in the  highest position (lowest  scraper
clearance) to give  a 1/8" clearance between the  scraper
bar and the ground.  Use  a middle position if the surface
to be cleared is uneven.
CHECK ENGINE OIL LEVEL (See Fig. 21)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
1.
2.
Check engine oil with snow thrower on level ground.
Remove oil  fill cap/dipstick  and wipe clean,  reinsert
the dipstick and  screw tight, wait  for a few seconds,
remove and read  oil level. If  necessary, add oil  until
“FULL” mark on dipstick is reached. Do not overfill.
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
ADD GASOLINE (See Fig. 21)
Fill fuel tank to bottom of tank filler neck.  Do not over-
fill.  Use fresh, clean,  regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
1.
2.
Shut off engine and wait for all moving parts to stop.
Adjust skid plates by  loosening the rear 1/2" hex nut
only,thenmovingskidplatetodesiredposition.Besure
both plates are adjusted evenly. Tighten securely.
WARNING:  Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
HIGH POSITION
LOW GROUND
CLEARANCE)
CAUTION: Alcohol blended fuels  (called gas-
ohol or using ethanol or methanol) can attract
moisture which  leads to  separation  and for-
mation of acids during storage. Acidic gas can
damage the fuel system of an engine while in
storage.   To avoid engine  problems, the fuel
system should  be emptied before  storage of
30 days  or longer.   Drain  the gas  tank, start
the  engine and  let it  run  until the  fuel lines
and carburetor are empty. Use fresh fuel next
season. SeeStorageInstructionsforadditional
information.  Never  use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
(
AUGER
HOUSING
SKID PLATE
/2" HEX NUT
1
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 19
SCRAPER BAR
The scraper bar is not adjustable, but is reversible.  After
considerable use it may become worn.  When it has worn
almost to  the  edge of  the housing,  it  can be  reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
CHOKE CONTROL
THROTTLE    PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
TO USE DRIFT CUTTERS (See Fig. 20)
SAFETY
IGNITION
KEY
Use the drift cutters to cut through deep snowdrifts that are
higher than the front of the snow thrower.
Loosen  upper adjustment  nut enough  to  allow drift
cutter to be raised to highest position and tighten nut
securely. Repeat for opposite side of snow thrower.
AUGER
HOUSING
GASOLINE
FILLER CAP
STORAGE
POSITION
DRIFT
CUTTER
FUEL SHUT-
OFF VALVE
RECOIL
STARTER
HANDLE
STARTER BUTTON
POWER CORD PLUG
ADJUST-
MENT NUT
NOTE:  ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 20
12
FIG. 21
Product Specification
CategoriesHusqvarna Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2006, 2007, 2008
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandHusqvarna, Snow Blower
Document File TypePDF
Publisherhusqvarna.com
Wikipedia's PageHusqvarna
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website