FUEL HANDLING
Fuelmix
Mixing
•
Always mix the petrol and
IMPORTANT! The chain saw is equipped with a two-stroke
engine and must always been run using a mixture of petrol and
two-stroke engine oil. It is important to accurately measure the
amount of oil to be mixed to ensure that the correct mixture is
obtained. When mixing small amounts of fuel, even small
inaccuracies can drastically affect the ratio of the mixture.
oil in a clean container
intended for fuel.
•
Always start by filling half
the amount of the petrol to
be used. Then add the
entire amount of oil. Mix
(shake) the fuel mixture.
Add the remaining amount
of petrol.
!
Always provide for good ventilation when
handling fuel.
•
Mix (shake) the fuel mixture
thoroughly before filling the
saw’s fuel tank.
Petrol
•
•
•
Use good quality unleaded
or leaded petrol.
The lowest octane
•
•
Do not mix more than max.
one month’s supply of fuel.
recommended is 90.
If you run the engine on a
lower octane grade than 90
so-called, knocking can
occur. This gives rise to a
high engine temperature,
which can result in serious
engine damage.
If the saw is not used for
some time the fuel tank
should be emptied and
cleaned.
•
When working with
continuous high revs (e.g.
delimbing) a higher octane
grade is recommended.
Two-stroke oil
•
For the best results use HUSQVARNA two-stroke oil, which is
especially developed for chain saws. Mixing ratio 1:50 (2%).
•
If HUSQVARNA two-stroke oil is not available, you may use
another two-stroke oil of good quality that is intended for air
cooled engines. Contact your dealer when selecting an oil.
Mixing ratio 1:33 (3%)-1:25 (4%).
Chain oil
•
•
Never use two-stroke oil intended for water cooled outboard
motors, so-called, outboard oil.
• The chain lubrication
system is automatic. Always
use special chain oil with
good adhesive
Never use oil intended for four-stroke engines.
characteristics.
•
In countries where no
special chain oil is available,
EP 90 transmission oil can
be used.
Gasolin
Benzin
Essence
Gasolina
Lit.
5
10
15
Oil • Öl
Huile • Aceite
Lit.
•
Never use waste oil. This
results in damage to the oil
pump, the bar and the
chain.
2
%(1:50) 3%(1:33) 4%(1:25)
0,10
0,20
0,30
0,40
0,15
0,30
0,45
0,60
US
fl. oz.
0,20
0,40
0,60
0,80
•
•
It is important to use oil of
the right viscosity according
to the air temperature.
20
US
gallon
In temperatures below 0 C
o
F) some oils become
too viscous. This can
(32
o
2%(1:50)
2 1/2
3%(1:33) 4%(1:25)
3 3/4
9 3/4
1
5 1/8
12 7/8
25 3/4
overload the oil pump and
result in damage to the oil
pump components.
2
1/2
5
6 1/2
12 7/8
19 1/4
•
Contact your servicing
dealer when choosing chain
oil.
26
– English
| Categories | Chainsaw Manuals, Husqvarna Chainsaw Manuals |
|---|---|
| Tags | Husqvarna 40, Husqvarna 45 |
| Model Year | 1999 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Product Brand | Husqvarna, Chainsaw |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Husqvarna 40 45 Chainsaw Owners Manual 4.0 out of 4.0 based on 1 product reviews. good manual details are hard to find. Finally a manual that i misplaced is obtainable