Muffler Diffuser
MAINTENANCE SCHEDULE
Spark
Lubricate bar
Arresting
Screen
Muffler
Cover
sprocket hole . . . . . . . After each use
Check:
Fuel mixture level . . . . Before each use
Bar lubrication. . . . . . . Before each use
Chain tension . . . . . . . Before each use
Chain sharpness . . . . Before each use
For damaged parts . . Before each use
For loose caps . . . . . . Before each use
For loose fasteners. . . Before each use
For loose parts . . . . . . Before each use
Inspect and Clean:
Screws
Muffler
Body
Muffler
Cover
CLEANING THE SPARK ARREST-
ING SCREEN
Bar . . . . . . . . . . . . . . . . Before each use
Complete saw. . . . . . . After each use
Air filter . . . . . . . . . . . . . Every 5 hours*
Chain brake . . . . . . . . Every 5 hours*
spark arresting screen
Cleaning is required every 25 hours of op-
eration or annually, whichever comes first.
S
S
S
Loosen and remove the 2 muffler cover
screws.
and muffler . . . . . . . . . Every 25 hours*
Replace spark plug . Yearly
Remove the muffler cover (cover snaps off
muffler body).
Replace fuel filter . . . Yearly
Remove muffler diffuser and spark arrest-
ing screen assembly. Notice the orienta-
tion of these parts for reassembling.
*
Hours of Operation
S Clean the spark arresting screen with a wire
brush. Replace screen if breaks are found.
S Replace any broken or cracked muffler
parts.
S Reinstall diffuserand spark arresting screen
assembly with round holes facing up.
AIR FILTER
CAUTION: Do not clean filter in gasoline
or other flammable solvent to avoid creating
a fire hazard or producing harmful evapora-
tive emissions.
S
Reinstall muffler cover and 2 screws (7-8
ft/lbs).
CARBURETOR ADJUSTMENTS
Your carburetor is equipped with limiter
caps.
Carburetor adjustment is a compli-
cated task. We recommend that you take
your unit to an Authorized Service Dealer.
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
BAR MAINTENANCE
If your saw cuts to one side, has to be forced
through the cut, or been run with an improper
amount of bar lubrication it may be neces-
sary to service your bar. A wornbar will dam-
age your chain and make cutting difficult.
After each use, ensure ON/STOP switch is
in the STOP position, then clean all sawdust
from the guide bar and sprocket hole.
5
hours of operation.
S Clean the cover and the area around it to
keep dirt and sawdust from falling into the
carburetor chamber when the cover is re-
moved.
S Remove the parts as illustrated below.
S Wash the filter in soap and water.
To maintain guide bar:
S Move ON/STOP switch to the STOP posi-
tion.
Cylinder
Cover
S Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from
saw.
S Clean the oil holes and bar groove after
each 5 hours of operation.
Air Filter
Remove Sawdust From
Guide Bar Groove
Sprocket Hole
Oil Holes
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
As the unit is used, carbon deposits build up
on the muffler and spark arresting screen,
and must be removed to avoid creating a fire
hazard or affecting engine performance.
Replace the spark arresting screen if breaks
occur.
S Add lubricant to sprocket hole after each
use.
S Burring of guide bar rails is a normal
process of rail wear. Remove these burrs
with a flat file.
13
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 2750, Poulan 2775, Poulan 2900, Poulan 3050 |
| Model Year | 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)