S Allow the engine to run for approximately
five seconds. Then, squeeze and release
throttle trigger to allow engine to return to
idle speed.
STARTING
WARNING: The chain must not move
when the engine runs at idle speed. If the
chain moves at idle speed refer to CARBU-
RETOR ADJUSTMENT within this manual.
Avoid contact with the muffler. A hot muffler
can cause serious burns.
For a warm engine:
S Pull the choke/fast idle lever out to the full
extent, then push the choke/fast idle lever
back in completely (to the OFF CHOKE
position).
S Slowly press the primer bulb six times.
S Pull the starter rope quickly with yourright
hand until the engine starts.
To stop the engine move the switch to the
STOP or OFF position.
To start the engine hold the saw firmly on
the ground as illustrated. Make sure the
chain is free to turn without contacting any
object.
S Squeeze and release throttle trigger, al-
lowing engine to idle.
Difficult starting or flooded engine:
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Use only 15”---18” of rope per pull.
Hold saw firmly while pulling starter rope
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ignition
switch is in the ON or START position.
Starting could require pulling the starter
rope handle many times depending onhow
badly the unit is flooded. If engine fails to
start, refer to troubleshooting chart or call
1-800-554-6723.
CUTTING METHODS
Important points to remember
When pulling the starter rope, do not use
the full extent of the rope as this can
cause the rope to break. Do not let starter
rope snap back. Hold the handle and let
the rope rewind slowly.
IMPORTANT POINTS
S
Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials,
etc.
For cold weather starting, start the unit at
FULL CHOKE; allow the engine to warm
up before squeezing the throttle trigger.
Do not cut material with the choke/fast idle
lever at the FULL CHOKE position.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary.
S Keep the chain out of dirt and sand. Even
a small amount of dirt will quickly dull a
chain and thus increase the possibility of
kickback.
For
cold engine or warm engine after
running out of fuel:
NOTE: In the following steps, when the
choke/fast idle lever is pulled out to the full
extent, the correct throttle setting forstarting
is set automatically.
S Practice cutting a few small logs using the
following techniques to get the “feel” of
using your saw before you begin a major
sawing operation.
S Squeeze throttle trigger and allow engine
to reach full speed before cutting.
S Begin cutting with saw frame against log.
S Keep the engine at full speed the entire
time you are cutting.
ON/STOP
Switch
Primer
Bulb
S Allow chain to cut for you. Exert only light
pressure. If you force the cut, damage to
bar, chain, or engine can result.
S Move switch to the STARTor ON position.
S Pull the choke/fast idle lever out to the full
extent.
S
Release the throttle trigger as soon as the
cut is completed, allowing the engine to
idle. If you run the saw at full throttle with-
out a cutting load, unnecessary wear can
occur to the chain, bar, and engine.
Choke Lever
S To avoid losing control when cut is com-
plete, do not put pressure on the saw at
the end of the cut.
S Stop the engine before setting the saw
down after cutting.
S Slowly press the primer bulb six times.
S Pull the starter rope quickly with yourright
hand 5 times, then push the choke/fast
idle lever in completely (to the OFF CHO-
KE position).
TREE FELLING TECHNIQUES
Carefully plan your sawing operation in ad-
vance. Clear the work area. You need a
clear area all around the tree so you can
have secure footing. Study the natural con-
S Pull the starter rope quickly with yourright
hand until the engine starts.
7
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 2250, Poulan 2450, Poulan 2550 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)