Poulan Pro 230 260 Chainsaw Owners Manual

S  Carefully plan your sawing operation in ad-
vance.
Final cut here. 2 inches above
First cut center of notch.
S  Clear the workarea. You need a clear area
all around the tree so you can have secure
footing.
S  Study  the   natural  conditions   that   can
cause the tree to  fall in a particular direc-
tion.
Notch
Natural conditions  that can  cause a tree to
fall in a particular direction  include:
S  The wind direction and speed.
S  The lean of  the tree.   The lean  of a  tree
might not  be apparent  due  to uneven  or
sloping terrain. Use a plumb or level to de-
termine the direction of  tree lean.
S  Weight and branches on one side.
S  Surrounding trees and obstacles.
Look for decay and rot.  If the trunk is rotted,
Second cut
Hinge holds tree on stump and helps
control fall
Opening
of felling
cut
it  can snap  and  fall toward  the
operator.
Check for  broken or dead  branches which
can fall on you while cutting.
Make sure there is enough room for the tree
to  fall.    Maintain  a  distance  of  2-1/2  tree
lengths from the nearest person or other ob-
jects. Engine noise can drown out a warning
call.
Remove dirt, stones,  loose bark, nails,  sta-
ples, and wire from the tree where cuts areto
be made.
Closing of
notch
Plan a clear retreat path to the rear and diag-
NOTE:
Before felling  cut is complete,  use
onal to the line of fall.
wedges to open  the cut when necessary to
control the direction of fall. To avoid kickback
and  chain  damage,  use   wood  or  plastic
wedges, but never steel or iron wedges.
S  Be alert to signs  that the tree  is ready to
fall: cracking sounds,  widening of the fell-
Plan a clear retreat path
Direction of Fall
ing   cut,   or   movement   in   the   upper
branches.
45
_
S  As tree starts to fall, stop saw, put it down,
and get away quickly on your planned  re-
treat path.
S  Be extremely cautious with partially fallen
trees that may be poorly supported.  When
a tree doesn’t fall completely,  set the saw
aside and pull  down the tree with a cable
winch, block and tackle, or tractor. Do not
cut down  a partially  fallen tree  with your
saw.
FELLING LARGE TREES
(6
inches in diameter or larger)
The notch method is used to fell large trees.
A notch is cut on the side of the tree in the de-
sired direction  of  fall.   After a felling  cut  is
made on the  opposite side  of tree, the tree
will tend to fall into  the notch.
CUTTING A FALLEN TREE
NOTE: If the tree has large buttress  roots,
(BUCKING)
Bucking is the term used  for cutting a fallen
tree to the desired log size.
remove them before making the  notch.
NOTCH CUT AND FELLING THE
TREE
WARNING: Do not stand on the  log
being cut.  Any portion can roll causing loss
of footing and control. Do not stand downhill
of the log being cut.
S  Make notch cut  by cutting  the top  of the
notch first. Cut through 1/3 of the diameter
of the tree. Next complete the notch bycut-
ting  the  bottom  of the  notch.  See  illus-
trated. Once  the notch is  cut remove the
notch of wood from the tree.
IMPORTANT POINTS
S  Cut only one log at a time.
S  After removing the  cutout of wood, make
the felling  cut on the opposite  side of the
notch. This is done by making a cut about
two inches  higher than  the center  of the
notch.  This will leave enough uncut wood
between  the felling  cut and  the notch  to
form a hinge.  This hinge will help prevent
the tree from falling in the wrong direction.
S  Cut shattered wood  very carefully; sharp
pieces of wood could be flung toward oper-
ator.
S  Use a sawhorse to cut small logs.  Never
allow another person to hold the  log while
cutting and never hold the log with your leg
or foot.
S  Do not cut  in an area  where logs, limbs,
and roots are tangled  such as in a blown
10
Product Specification
CategoriesChainsaw Manuals, Poulan Pro Chainsaw Manuals
Tags,
Model Year2000
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 15 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website