Computed kickback angle (CKA) Table
BAR
P/N
952044815
MODEL
Length
20”
CHAIN P/N
952051310
CKA without chain brake
19_
2
95
NOTE:
This saw complies with Federal
Loosen and remove the chain brake nuts
and the chain brake from the saw.
Remove the plastic shipping spacer (if
present).
S
S
OSHA regulations for commercial logging.
to
SAFETY
NOTICE:
Exposure
vibrations through prolonged use of gasoline
powered hand tools could cause blood
vessel or nerve damage in the fingers,
Location of shipping spacer
hands,
and joints of people prone to
circulation disorders or abnormal swellings.
Prolonged use in cold weather has been
linked to blood vessel damage in otherwise
healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in the
fingers, hands, or joints, discontinue the use
of this tool and seek medical attention. An
anti-vibration system does not guarantee the
avoidance of these problems. Users who
operate power tools on a continual and
regular basis must monitor closely their
physical condition and the condition of this
tool.
Chain Brake
Nuts
Chain Brake
Bar Tool
SPECIALNOTICE: Yoursaw is equipped
with a temperature limiting muffler and spark
S
Turn adjusting screw on bar counterclock-
wise to move the tensioning rack as far as
it will go toward the front of the bar.
arresting
screen
which
meets
the
requirements of California Codes 4442 and
4443.
All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines
to be equipped with a spark arrestor screen.
If you operate a chain saw in a state or locale
where such regulations exist, you are legally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
Adjusting
Screw
Tensioning Rack
section
for maintenance of the Spark
S
Mount the bar as illustrated.
S Slide the bar behind clutch drum until bar
stops against clutch drum sprocket.
S Prepare the chain by checking the proper
direction. Without following the illustration
it is easy to place the chain on the saw in
the wrong direction. Use the illustration of
the chain to determine the proper direc-
tion.
Arrestor.
Failure to follow all Safety Rules and Precau-
tions can result in serious injury. If situations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your Authorized Service
Dealer or call 1-800--554--6723.
ASSEMBLY
S Place the chain onto the sprocket located
behind the clutch drum (see illustration).
Fit the chain between the teeth in the
sprocket.
Protective gloves (not provided) should be
worn during assembly.
S Start at the top of the bar and fit chain into
ATTACHINGTHEBAR&CHAIN (If not
groove around the guide bar.
already attached)
Pull the bar forward until the chain is snug
in the groove of the bar. Ensure all drive
links are in the bar groove.
S
WARNING: If received assembled,
repeat all steps to ensure your saw is prop-
erly assembled and all fasteners are secure.
Always wear gloves when handling the
chain. The chain is sharp and can cut you
even when it is not moving!
S Hold guide bar against the saw frame and
install the chain brake.
S Replace the chain brake nuts and tighten
finger tight. Once the chain is tensioned
you will need to tighten chain brake nuts.
6
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro 295 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)