A. Unhook the upper cable end from the hole in the
control bar bracket (Fig. 7).
2. Remove the fuel tank cap and use a pump-type syphon
to drain the fuel into a clean gasoline container.
B. Slide the spring cover up the cable to expose the
cable adjuster (Fig. 7).
3. Start the engine and allow it to run until it consumes
all the fuel in the fuel tank and stops running. Repeat
this step two more times to ensure that the fuel tank is
empty.
C. Unhook the Z fitting from the cable adjuster and
position it in the top or bottom hole on the adjuster
to obtain a gap of 1/16 to 1/8 in. (0.16 to 0.32 cm)
between the control bar bracket and the handle
(Fig. 13).
Replacing the Scraper
Before each season, inspect the scraper for wear. If the
thickness of the scraper’s bottom is less than 1/16 in.
(1.6 mm), replace the scraper (Fig. 15).
D. Install the spring cover over the cable adjuster.
E. Install the upper cable end into the bottom hole in
the control bar bracket (Fig. 8).
2
1
2
1
3
634
Figure 15
630
Figure 14
1.
Scraper
2. 1/16 in.
1.
2.
Spring cover
Z fitting
3. Cable adjuster
Note: The running time and the roughness of the driveway
or sidewalk determines the scraper wear rate.
5.
Check the adjustment (refer to steps 2 and 3 above).
1. Stop the engine.
After extended use, the drive belt may wear and lose its
proper belt tension. Improper belt tension causes belt
slippage and decreases the performance under a heavy
load. Belt slippage may occur after two or three seasons of
normal usage (10 to 15 hours). If the drive belt slips
(continuously squeals) under a heavy load, increase the
belt tension by doing one of the following steps:
2. Drain the fuel from the fuel tank. Refer to Emptying
the Fuel Tank on page 13.
3.
4.
Tip the snowthrower forward onto its front housing.
Remove three carriage bolts and the locknuts holding
scraper in place (Fig. 16).
5.
Remove the scraper by sliding it to the right and down.
•
For Models 38413 and 38419: Reposition the spring
end in the bottom hole of the control bar bracket
(Fig. 7).
•
For Models 38439, 38440, and 38445: Reposition the
upper cable end into the upper hole of the control bar
bracket (Fig. 8).
2
Using the incorrect adjusting hole in the control bar
bracket can reduce the drive belt life. Occasional belt
slippage (squealing) may occur in extremely wet
conditions due to moisture in the drive system. To remove
moisture, start the rotor and operate it without a load for
30 seconds. Once you remove the moisture, the drive belt
should not slip.
1
644
Figure 16
1.
Scraper
2.
Carriage bolts and
locknuts
Emptying the Fuel Tank
1.
Stop the engine and remove the key from the switch.
13
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38413, Toro CCR 2450 |
| Model Number | 38413 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 000000001 - 000999999 |
| Product Name | Toro CCR 2450 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 1000/2400/2500, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Toro |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | R-tek |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)