2
2. Cover the hole in the center of the primer with your
thumb and push the primer in twice. In extremely cold
temperatures, repeat this step as necessary.
1
3
Note: Do not use the choke and the primer when starting a
warm engine.
111
Figure 9
3.
For a recoil starter: Hold the snowthrower with one
hand and pull the recoil starter vigorously with the
other hand.
1.
2.
Add oil to small amount of
gasoline
3.
Add remaining amount of
gasoline
Install cap and shake can
to mix
For an electric starter:
A. Connect the power cord to the snowthrower and to
a standard household power outlet.
We recommend using a stabilizer/conditioner for all Toro
gasoline-powered products during operation and storage.
A fuel stabilizer/conditioner cleans the engine during
operation and prevents gum-like varnish deposits from
forming in the engine during storage. A fuel
stabilizer/conditioner works best when you mix it with
fresh gasoline.
B. Push the starter button.
Run the electric starter no more than ten times at
intervals of five seconds on, then five seconds off.
If the engine does not start after this attempt, wait
at least 40 minutes to allow the starter to cool
before attempting to start it again.
Note: If you use Toro Heavy Duty 50:1 All Season 2-Cycle
Engine Oil with Fuel Stabilizer, you do not need to add a
fuel stabilizer/conditioner.
IMPORTANT: Running the electric starter extensively
can overheat and damage the starter.
IMPORTANT: Do not use fuel additives except a fuel
stabilizer during storage. Do not use fuel stabilizers
with an alcohol base such as ethanol, methanol, or
isopropanol.
If the engine does not start after the second
attempt, bring the snowthrower to an Authorized
Service Dealer for service.
C. When the engine starts, disconnect the power cord
from the snowthrower and the outlet.
Operation
4.
With the engine running, push in the choke slowly.
Operating Controls
Stopping the Engine
The snowthrower control panel contains a key switch, a
primer, a recoil starter, and an electric start button. The
choke is just below the control panel (Fig. 10).
Turn the key to the Off position, and wait for all moving
parts to stop before leaving the operating position.
5
Starting the Rotor Blades
To start the rotor blades, squeeze the control bar and
handle together.
3
1
Stopping the Rotor Blades
6
4
Release the control bar to stop the rotor blades.
2
642
Note: When you release the control bar, the rotor blades
stop, but the engine continues to run.
Figure 10
1.
2.
3.
4.
Key switch
Primer
5.
Elec. start button (electric
start models only)
Adjusting the Discharge Chute
6.
Cord connection (electric
start models only)
Recoil start
Choke
Models 38413 and 38419 only
Move the chute handle left and right to adjust the
direction of the snow stream (Fig. 11). The chute deflector
handle on top of the discharge chute controls the height of
the snow stream. Do not overtighten the chute deflector
mounting locknuts.
Starting the Engine
1.
Turn the key to the On position and pull the choke out.
10
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38419, Toro CCR 3600 |
| Model Number | 38419 |
| Model Year | 2000 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 200000001 - 200012436 |
| Product Name | Toro CCR 3600 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 1000/2400/2500, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Toro |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | R-tek |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)