FUEL HANDLING
Fuel
Mixing ratio
1:50
(2%) for all engines.
Note! The machine is equipped with a two-stroke engine and
must always been run using a mixture of gasoline and two-
stroke engine oil. It is important to accurately measure the
amount of oil to be mixed to ensure that the correct mixture is
obtained. When mixing small amounts of fuel, even small
inaccuracies can drastically affect the ratio of the mixture.
Gasoline, litre
Two-stroke oil, litre
2% (1:50)
0,10
5
10
0,43/0,20
0,30
15
20
0,40
WARNING! Always ensure there is adequate
ventilation when handling fuel.
!
US gallon
US fl. oz.
2%
(1:50)
1
2 1/2
6 1/2
12 7/8
Gasoline
2
5
1/2
Mixing
•
This engine is certified to operate on unleaded
gasoline.
•
•
Use good quality unleaded gasoline.
CAUTION! Engines equipped with catalytic
converters must be run on unleaded fuel mixtures.
•
Leaded gasoline will destroy the catalytic converter and it
will no longer serve its purpose. The green fuel cap on
saws fitted with catalytic converters means that only
unleaded gasoline can be used.
•
The lowest recommended octane grade is 87
((RON+MON)/2).
If you run the engine on a lower octane
•
•
Always mix the gasoline and oil in a clean container
intended for fuel.
grade than 87 so-called knocking can occur. This gives
rise to a high engine temperature and increased bearing
load, which can result in serious engine damage.
Always start by filling half the amount of the gasoline to be
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of gasoline.
•
When working with continuous high revs (e.g. limbing) a
higher octane is recommended.
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
Environment fuel
•
•
Do not mix more than one month’s supply of fuel at a time.
HUSQVARNA recommends the use of alkylate fuel or
environmental fuel for four-stroke engines blended with two-
stroke oil as set out below. Note that carburetor adjustment
may be necessary when changing the type of fuel (see
instructions under the heading Carburetor).
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Chain oil
•
We recommend the use of special oil (chain oil) with good
adhesion characteristics.
Running-in
Avoid running at a too high speed for extended periods during
the first 10 hours.
Two-stroke oil
•
•
•
For best results and performance use HUSQVARNA two-
stroke engine oil, which is specially formulated for our air-
cooled two stroke-engines.
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
•
•
•
Never use waste oil. This results in damage to the oil
pump, the bar and the chain.
Never use oil intended for four-stroke engines.
It is important to use oil of the right grade (suitable
viscosity range) to suit the air temperature.
In temperatures below 0°C (32°F) some oils become too
viscous. This can overload the oil pump and result in
damage to the oil pump components.
•
Contact your service agent when choosing chain oil.
English – 17
| Categories | Chainsaw Manuals, Husqvarna Chainsaw Manuals |
|---|---|
| Tags | Husqvarna 336 |
| Model Year | 2001, 2002, 2003, 2004, 2005, 2006 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Product Brand | Husqvarna, Chainsaw |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)