McCulloch 441 442 Chainsaw Owners Manual

IMPORTANT POINTS TO REMEMBER
Whenpullingthestarterrope,donotusethefull
extentoftheropeas   this can causethe ropeto
break. Do not let starter rope snap back. Hold
the handle and let the rope rewind slowly.
For cold weather starting, start the unit atfull
choke; allow the engine to warm up before
squeezing the throttle trigger.
completely  (to the  OFF CHOKE  position)
and then following the warm engine starting
procedure  listed  above.  Ensure  the ON/
STOP switch is in the ON position. Starting
could require pulling the starter rope handle
many times dependingon how badly theunit
is flooded. If engine fails to start, refer to the
TROUBLESHOOTING TABLE.
NOTE:  Do not cut material with the choke/
CHAIN BRAKE
fast idle lever at the FULL CHOKE position.
WARNING: If the brake band is worn
too thin it may break when the chain brake is
triggered. With a broken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by  an authorized service
dealer ifany partis worntoless  than 0,02 (0,5
mm) thick. Repairs onachainbrakeshouldbe
made by  an authorized service dealer.  Take
your unit to the place of purchase if purchased
fromaservicingdealer,or   tothenearestautho-
rized master service dealer.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
NOTE:   In the  following steps,  when the
choke/fast idle lever is pulled out to  the full
extent, the correct throttle setting for starting
is set automatically.
ON/STOP SWITCH
(SIDE VIEW)
S  This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
ON
STOP
S  Theinertiaactivated chainbrake  is activated
if the front hand guard is pushed forward, ei-
ther manually or by centrifugal force.
1.
Move ON/STOP switch to the ON posi-
tion.
S  Ifthebrakeis  already activated,it is disen-
gagedby pullingthefronthandguardback
toward the front handle as far as possible.
S  Whencuttingwiththesaw,thechainbrake
must be disengaged.
2.
3.
Slowly press primer bulb 6 times.
Pull out choke/fast idle to the full extent
(to the FULL CHOKE position).
Pull the starter rope sharply 5 times with
your right  hand. Then,  proceed to  the
next step.
4.
Disengaged
Engaged
NOTE: If the engine sounds as if it is trying
to start before the 5th pull, stop pulling and
immediately proceed to the next step.
5.
Push the choke/fast idle  lever in to the
HALF CHOKE position.
CHOKE/FAST IDLE LEVER
(SIDE VIEW)
Braking function control
CAUTION:
The  chain  brake  must  be
checked  several times  daily.  The  engine
mustberunningwhenperformingthisproce-
dure. This is theonly instancewhen thesaw
should be placed on the ground with the en-
gine running.
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the  chain brake  by turning  your  left wrist
against  the hand  guard  without releasing
your grip around the front handle. The chain
should stop immediately.
Choke/
fast idle lever
OFF
HALF
FULL
6.
7.
Pull the  starter rope  sharply with  your
right hand until the engine starts.
Allow theenginetorunfor  approximately
30
seconds. Then, squeeze and release
throttletriggerto  allow enginetoreturnto
idle speed.
STARTING A WARM ENGINE
1.
2.
3.
MoveON/STOP switchtotheONposition.
Slowly press the primer bulb 6 times.
Pull the choke/fast idle  lever out to the
HALF CHOKE position.
Inertia activating function control
WARNING
: When performing the fol-
lowing procedure, the engine must be turned
off.
4.
5.
Pull the  starter rope  sharply with  your
right hand until the engine starts.
Squeeze and release  throttle trigger to
allow engine to return to idle speed.
Grip therear handlewith your right handand
the front handle with your left hand. Hold the
chain saw approximately 14” (35 cm) above
a stump or other wooden surface. Release
your grip  on the front  handle and  use the
weight of the saw to let the top of the guide
bar  fall  forward  and  contact  the  stump.
When the tip of the  bar hits the stump, the
brake should activate.
DIFFICULT STARTING (or starting a
flooded engine)
The engine may  be flooded with too much
fuel  if  it  has  not   started  after  10  pulls.
Flooded engines can be cleared of  excess
fuel by pushing  the choke/fast idle lever in
9
Product Specification
CategoriesChainsaw Manuals, McCulloch Chainsaw Manuals
Tags,
Model Year2001, 2002, 2003, 2004, 2005, 2006
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 16 pages
LanguageEnglish
Product BrandMcCulloch. Support Phone for US: Wheeled (Mowers, Tractors, Tillers, Snow Throwers) - 1-800-849-1297
McCulloch Handheld (Chainsaws, Trimmers, Blowers, Edgers) - 1-800-554-6723 All McCulloch Products - 1-800-521-8559, Chainsaw
Document File TypePDF
Publishermcculloch.com
Wikipedia's PageMcCulloch Motors
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website