FUELING & LUBRICATION
STARTING
WARNING: Remove fuel cap slow-
WARNING:
The chain must not
ly when refueling.
move when the engine runs at idle speed. If
the chain moves at idle speed refer to CAR-
FUELING ENGINE
BURETOR
ADJUSTMENT
within
this
This engine is certified to operate on un-
leaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
manual. Avoid contact with the muffler. A hot
muffler can cause serious burns.
To stop the engine move the ON/STOP
switch to the STOP position.
2-cycle
air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brand synthetic oil is recommended. A 40:1
ratio is obtained by mixing 3.2 ounces of oil
with 1 gallon of unleaded gasoline. Included
with this saw is a 3.2 ounce container of Pou-
lan/Weed Eater brand synthetic oil. Pour the
entire contents of this container into 1 gallon of
gasoline to achieve the proper fuel mixture.
DO NOT USE automotive or boat oil. These
oils will cause engine damage. When mixing
fuel follow the instructions printed on the
container. Always read and follow the safety
rules listed under HANDLE FUEL WITH
CAUTION.
To start the engine hold the saw firmly on
the ground as illustrated. Make sure the
chain is free to turn without contacting any
object.
Use only 15”--18” of rope per pull.
Hold saw firmly while pulling starter rope.
Starter rope handle
Left hand
on front
handle
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubri-
cation. Lubrication is provided by the auto-
matic oiler system when the oil tank is kept
filled. Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheating
shown by smoke coming from the chain and/
or discoloration of the bar.
Right foot through rear handle
IMPORTANTPOINTS TOREMEMBER
When pulling the starter rope, do not use the
full extent of the rope as this can cause the
rope to break. Do not let starter rope snap
back. Hold the handle and let the rope re-
wind slowly.
In freezing weather oil will thicken, making it
necessary to thin bar and chain oil with a
small amount (5 to 10%) of #1 Diesel Fuel or
NOTE: Do not attempt to cut material with
the fast idle lock button in the locked position.
kerosene.
Bar and chain oil must be free
flowing for the oil system to pump enough oil
for adequate lubrication.
STARTING A COLD ENGINE (or
warm engine after running out of
fuel)
Genuine PoulanRbarand chain oil is recom-
mended to protect your unit against exces-
sive wear from heat and friction. PoulanR
oil resists high temperature thinning. If Pou-
lanR bar and chain oil is not available, use a
good grade SAE 30 oil.
ON/STOP SWITCH
(SIDE VIEW)
ON
S Never use waste oil for bar and chain lubri-
cation.
STOP
S Always stop the engine before removing
the oil cap.
S Move ON/STOP switch to the ONposition.
IMPORTANT
Pull choke knob out to the full extent.
Slowly press primer bulb 6 times.
Squeeze and hold throttle trigger. With
thumb press fast idle lock down; then re-
lease throttle trigger.
S
S
S
Experience indicates that alcohol--blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads
to separation and formation of acids during
storage.
Acidic gas can damage the fuel
Fast idle lock button
system of an engine while in storage.
To
avoid engine problems, the fuel system
should be emptied before storage for 30
days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel next
Throttle
lock--out
Choke knob
Throttle
trigger
season.
See STORAGE section for addi-
tional information.
S Sharply pull the starter rope handle 5times
with your right hand. Then, proceed to the
next step.
NOTE: If the engine sounds as if it is try-
ing to start before the 5th pull, stop pulling
and immediately proceed to the next step.
9
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 1950, Poulan 2025, Poulan 2050, Poulan 2075, Poulan 2150, Poulan 2150PR, Poulan 2155, Poulan 2175, Poulan 2350, Poulan 2375, Poulan LE-Series |
| Model Year | 2002 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)