S As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re-
treat path.
Undercutting involves cutting on the under-
side of the log with top of saw against the log.
When undercutting use light upward pres-
sure. Hold saw firmly and maintain control.
The saw will tend to push back toward you.
S DO NOT cut down a partially fallen tree
with your saw. Be extremely cautious with
partially fallen trees that may be poorly
supported. When a tree doesn’t fall com-
pletely, set the sawaside and pull down the
tree with a cable winch, block and tackle,
or tractor.
WARNING:
Never turn saw upside
down to undercut. The saw cannot be con-
trolled in this position.
Always make your first cut on the compres-
sion side of the log. The compression side of
the log is where the pressure of the log’s
weight is concentrated.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a fallen
tree to the desired log size.
First cut on compression side of log
WARNING: Do not stand on the log
being cut. Any portion can roll causing loss
of footing and control. Do not stand downhill
of the log being cut.
IMPORTANT POINTS
Second cut
Second cut
S Cut only one log at a time.
S Cut shattered wood very carefully; sharp
pieces of wood could be flung toward oper-
ator.
S Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cutting and never hold the log with your leg
or foot.
First cut on compression side of log
S Do not cut in an area where logs, limbs,
and roots are tangled such as in a blown
down area. Drag the logs into a clear area
before cutting by pulling out exposed and
cleared logs first.
BUCKING WITHOUT A SUPPORT
S Overcut through 1/3 of the diameter of the
log.
S Roll the log over and finish with a second
overcut.
TYPES OF CUTTING USED FOR
BUCKING
S Watch for logs with a compression side to
prevent the saw from pinching. See il-
lustrations for cutting logs with a compres-
sion side.
WARNING:
If saw becomes
BUCKING USING A LOG OR
pinched or hung in a log, don’t try to force it
out. You can lose control of the sawresulting
in injury and/or damage to the saw. Stop the
saw, drive awedge of plastic orwood into the
cut until the saw can be removed easily. Re-
start the sawand carefully reenter the cut. To
avoid kickback and chain damage, do not
use a metal wedge. Do not attempt to restart
your saw when it is pinched or hung in a log.
SUPPORT STAND
S
Remember your first cut is always on the
compression side of the log.
(Refer to the illustrations below for your
first and second cut)
S
S
Your first cut should extend 1/3 of the
diameter of the log.
Finish with your second cut.
Using a log for support
2
nd Cut
Use a wedge to remove pinched saw
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
Overcutting begins on the top side of the log
with the bottom of the saw against the log.
When overcutting use light downward pres-
sure.
1
st Cut
1
st Cut
Overcutting
Undercutting
2
nd Cut
12
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 1950, Poulan 2025, Poulan 2050, Poulan 2075, Poulan 2150, Poulan 2155, Poulan 2175, Poulan 2350, Poulan 2375 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)