Poulan P10530ESA Snow Blower Owners Manual

TO REMOVE WHEELS (See Fig. 24)
Remove the klik pin and remove wheel from axle.
NOTE: To seal punctures or prevent flat tires due  to slow
leaks, tire sealant may be purchased from your local parts
dealer.Tire sealant also prevents tire dry rot and corrosion.
IMPORTANT:When installing wheel, be sure to use the in-
nermost hole in axle and the wheel hub hole. To disengage
drive system from the wheels (for pushing or transporting
the snow  thrower), remove  klik pin from  wheel hub  and
insert pin into the outermost hole in axle only.
ENGINE
See engine manual.
CARBURETOR
Your  carburetor  is  not adjustable.  Engine  performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine  does not operate properly due  to
suspected carburetor problems, take your snow thrower to
a qualified service center.
KLIK PIN
OUTER HOLE
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be  dangerous and will
void the  warranty. If you  think the engine-governed  high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary adjustments.
INNER
HOLE
WHEEL
WHEEL HUB
FIG. 24
STORAGE
Immediately prepare your snow thrower for storage at the
end of the season or if the unit will not be used for 30 days
or more.
1.   Drain the fuel tank.
2.
Start the engine  and let it run until  the fuel lines and
carburetor are empty.
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
WARNING:   Never   store   the   snow
throwerwithgasolineinthetankinside
a building where fumes  may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gasappliance. Allowtheenginetocool
before storing in any enclosure.
Use fresh fuel next season.
NOTE:  Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow  the mix ratio found  on stabilizer container.
Run engine at  least 10 minutes after adding  stabilizer to
allow the stabilizer to reach the carburetor.Do not drain the
gas tank and carburetor if using fuel stabilizer.
SNOW THROWER
When snow  thrower is to  be stored for a  period of time,
clean it  thoroughly,  remove all  dirt, grease,  leaves,  etc.
Store in a clean, dry area.
ENGINE OIL
Drain oil  (with engine warm)  and replace with  clean en-
gine  oil. (See  “ENGINE” in  the Maintenance  section  of
this manual).
1.
Clean entire  snow thrower (See  “CLEANING” in the
Maintenance section of this manual).
2.
Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
CYLINDER
1.
2.
Remove spark plug.
Pour one ounce (30 ml) of oil through spark plug hole
into cylinder.
3.
4.
Lubricate as shown in the Maintenance section of this
manual.
3.
4.
Pullrecoilstarter  handleslowlyafewtimestodistribute
oil.
Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
Replace with new spark plug.
5.
Touch up  all rusted  or chipped paint  surfaces; sand
lightly before painting.
OTHER
Do not store gasoline from one season to another.
ENGINE
See engine manual.
FUEL SYSTEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuelhose,ortankduringstorage.Also,alcoholblendedfuels
(called gasohol or using ethanol or  methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
Replace your gasoline  can if your  can starts to  rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
Coveryoursnowthrowerwithasuitableprotectivecover
thatdoesnotretainmoisture.Do   notuseplastic.Plastic
cannotbreathe,whichallowscondensationtoformand
will cause your snow thrower to rust.
IMPORTANT: Never  cover  snow  thrower  while engine/
exhaust area is still warm.
18
Product Specification
CategoriesPoulan Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2002
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Snow Blower
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website