Poulan Pro 220 LE 260 LE Chainsaw Owners Manual

CARBURETOR ADJUSTMENTS
Loosen 3 screws on cylinder cover.
S
Your carburetor is equipped with limiter caps.
Carburetor adjustment is a  complicated task.
We recommend that you take your unit  to an
authorized service dealer. Damagewill occurif
you turn the needles beyond the limiter stops.
S  Remove the cylinder cover.
S  Pull off the spark plug boot.
S  Remove spark plug from  cylinder and dis-
card.
S  Replace with  Champion  RCJ--7Y  spark
plug and tighten  securely  with a 3/4 inch
socket wrench.  Spark plug gap should be
BAR MAINTENANCE
If your saw cuts to one side, has to be forced
through the cut, or been run with an improper
amount of bar lubrication it may be necessary
to service your bar.   A worn bar will damage
your chain and make cutting difficult.
0.025
inches.
S  Reinstall the spark plug boot.
S  Reinstall the cylinder  cover and 3 screws.
Tighten securely.
Screws
Cylinder
Cover
After each use, ensure ON/STOP switch is in
theSTOPposition,thenclean   allsawdust  from
the guide bar and sprocket hole.
Spark
Plug Boot
To maintain guide bar:
S  Move ON/STOP switch to the STOP  posi-
tion.
Spark
Plug
S  Loosen and remove chain  brake nuts and
chain brake.   Remove bar and  chain from
saw.
STORAGE
S  Clean the oil holes and bargroove aftereach
5
hours of operation.
WARNING:
Stop engine and allow
Remove Sawdust From
Guide Bar Groove
to cool, and secure the unit before storing or
transporting in a vehicle.  Store unit and fuel
in an area  where fuel vapors  cannot reach
sparks or open  flames from water  heaters,
electric  motors or  switches,  furnaces, etc.
Store unit with all guards in place. Position so
that  any  sharp object  cannot  accidentally
cause injury to passersby. Store the unit out
of reach of children.
Sprocket Hole
Oil Holes
S  Add lubricant  to  sprocket hole  after each
use.
S  Before storing, drain all fuel from  the unit.
S  Burring of guide barrails is a normal process
of rail wear. Remove these burrs with a flat
file.
Start engine and allow to run until it stops.
S
Clean the unit before storing. Pay particu-
lar attention to the air intake area, keeping
it free of debris. Use a mild detergent  and
sponge to clean the plastic  surfaces.
S  When rail top is uneven, use a flat file to re-
store square edges and sides.
File Rail Edges
and Sides
Square
S  Donot store the unit orfuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces,  etc.
S  Store in a dry area out of the reach of chil-
dren.
Worn Groove
Correct Groove
Replace guide bar when  the groove is worn,
the guide baris bent orcracked,orwhenexce-
ss heating or burring of the rails occurs. If re-
placement is necessary, use onlythe guidebar
specified for your saw in the repair parts list or
on the decal located on the chain saw.
CAUTION:
It is important to prevent gum
deposits from forming in essential fuel system
parts such  as  the carburetor,  fuel filter,  fuel
hose,  or  fuel  tank  during  storage.  Alcohol
blended fuels (called gasohol or using ethanol
or methanol) can attract moisture which leads
to  fuel mixture  separation  and  formation of
acids during storage. Acidic gas can damage
the engine.
CHAIN SHARPENING
Chain sharpening is a complicated task that
requires  special  tools.  We  recommended
you refer chain sharpening to a professional
chain sharpener.
NEED ASSISTANCE?
IGNITION TIMING
Ignition timing is  fixed and nonadjustable.
NEED ASSISTANCE?
SPARK PLUG
Call 1--800--554--6723.
The  spark  plug  should be  replaced  each
year to ensure the  engine starts easier and
runs better.
NEED SERVICE PART?
Contact your authorized  service dealer.
15
Product Specification
CategoriesChainsaw Manuals, Poulan Pro Chainsaw Manuals
Tags,
Model Year2002
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 18 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website