Check that the chain is sharpened correctly (See
below), in good working condition and that the
tension is correct. If the chain is irregularly worn, or if
the cutting teeth are only 3 mm high, the chain must
be replaced(fig.3).
The cutting side of the chain is composed of the cutting
link (fig.9) with a cutting tooth(fig.10) and a cutting limit
gauge(fig.11). The difference between these determines
the cutting depth; a file guide and a 4mm diameter round
file are needed to obtain good sharpening results; Follow
the instructions below: Once the chain has been
mounted and the tension is correctly adjusted, and the
Clean the air vents regularly to prevent motor
overheating.
Check that the switch and switch block function
correctly (to be performed with the chain brake
released): press the switch and the switch block and
control that they return to idle position as soon as
they are released; control that it is impossible to
press the switch without activating the switch block.
Check that the chain catcher and the right hand
guard are in correct condition without any visible
faults such as damaged material.
chain
brake
is
activated,
position
as
the
file
in
guide
the
perpendicular
to
the
bar
shown
illustration(fig.12), filing the cutting teeth at the angle
shown(fig.13), always working from the interior towards
the exterior, lessening the pressure during the return
stage (it is very important to follow the instructions
perfectly: excessive or insufficient sharpening angles, or
an incorrect file diameter will increase the risk of
kickback.) To obtain higher precision on side angles, it is
advisable to position the file so that it exceeds the upper
cutter by about 0.5 mm. File all the teeth on one side first,
then turn the machine over and repeat the operation.
Make sure that after sharpening operations, all teeth are
the same length and that the height of the depth gauge is
Every 2-3 hours of use
Control the bar condition, if necessary clean the
lubrication holes(fig.4) and the guide grooves(fig.5)
carefully; If the groove is worn or shows signs of deep
notching, it must be replaced. Turn the bar to ensure
even wear(fig.6). Clean the pinion regularly and check
that it has not been subject to excess wear(fig.7).
Lubricate the nose sprocket with bearing grease
through the hole shown in the illustration (fig.8).
0.6
mm lower than the upper cutter: check the height
using a proper template and file (with a flat file) all
protruding parts, rounding off the front part of the depth
gauge(fig.14), paying attention to not file the kickback
protection tooth(fig.15)
Chain sharpening (When necessary)
Every 30 hours use.
If the chain does not cut correctly, or requires hard
bar pressure against the wood, and if the sawdust is
very fine, this is a sign that it is not sharpened
correctly. If the cutting action produces no sawdust,
Take the machine to the Authorised Service Centre
for general revision and control check on brake
components.
this
means the cutting edge has been worn
PERIODS OF PROLONGED DISUSE
Always empty the fuel tank with the same precautions
used in filling it.
completely and the chain is pulverising the wood
cutting. A well-sharpened chain crosses
during
through the wood without effort or pressure and
produces large long wood shavings.
H. CUTTING TECHNIQUES
1,2,3,4,5,6,7,8,9,10,11,12,13,14
When using the machine, prevent: (fig.1)
- situations that can lead to kickback reactions.
During machine use: (fig.1)
-
cutting in conditions where the trunk could split
during cutting (wood under pressure, dry dead trees,
etc): sudden splitting can be very dangerous.
- When cutting on sloping ground, always work uphill
of the trunk to avoid being hit if the trunk should roll
downhill.
-
the bar or the chain from becoming blocked in the
cutting notch: if this should occur, disconnect the
machine from the main electricity supply and try to
- Release the switch after each cutting action:
prolonged dry running of the motor will provoke
raise the trunk using an appropriate tool as a lever; do serious damage.
not attempt to free the machine by shaking or pulling
as this could cause damage or injury.
- When felling trees, always finish the job: a partially
cut tree could break and fall.
ENGLISH - 8
| Categories | Chainsaw Manuals, Electramac Chainsaw Manuals, Electrolux Chainsaw Manuals, McCulloch Chainsaw Manuals |
|---|---|
| Tags | Electramac 235, Electramac 316, ElectraMac 416, McCulloch 235, McCulloch 316, McCulloch 416 |
| Model Year | 2004, 2005 |
| Download File |
|
| Language | English |
| Product Brand | Electrolux. Support phone for US: 877-435-3287 Fax: 706-228-6615
Monday - Saturday 8:00 a.m - 8:00 p.m (EST), Chainsaw, McCulloch. Support Phone for US: Wheeled (Mowers, Tractors, Tillers, Snow Throwers) - 1-800-849-1297
McCulloch Handheld (Chainsaws, Trimmers, Blowers, Edgers) - 1-800-554-6723 All McCulloch Products - 1-800-521-8559, Chainsaw |
| Document File Type | |
| Publisher | mcculloch.com |
| Wikipedia's Page | McCulloch Motors |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)