Poulan PO8527ESA 193452 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
12.
13.
Install  the two  (2)  hex bolts  and lock  washers  and
IMPORTANT: When installing  wheel, be sure to  use the
axle hole closest to the end  of the shaft – do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
holeinwheelhubarenotusedforyourmodelsnowthrower.
tighten securely.
INSTALLENGINEPULLEY-Placebeltinpulleygroove
and slide pulley on crankshaft. Install flat washer, lock-
washer and  bolt and  tighten securely  (30-35  ft. lbs.
torque).  Make sure belt is inside belt keeper.
NOTE: To seal punctures or prevent flat tires due  to slow
leaks, tire sealant may be purchased from your local parts
dealer.Tire sealant also prevents tire dry rot and corrosion.
14.
15.
INSTALL BELT  COVER and two (2)  screws. Tighten
securely.
ENGINE
See engine manual.
INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER  HEAD” in the
Assembly / Pre-Operation section of this manual.
CARBURETOR
TO REMOVE WHEELS (See Fig. 24)
•     Remove the klik pin and remove wheel from axle.
Your  carburetor  is  not adjustable.  Engine  performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine  does not operate properly due  to
suspected carburetor problems, take your snow thrower to
a qualified service center.
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY)
OUTER HOLE
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be  dangerous and will
void the  warranty. If you  think the engine-governed  high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary adjustments.
AXLE
WHEEL
WHEEL HUB
FIG. 24
STORAGE
Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.
FUEL SYSTEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
WARNING:   Never   store   the   snow
throwerwithgasolineinthetankinside
a building where fumes  may reach an
fuelhose,ortankduringstorage.Also,alcoholblendedfuels
open flame, spark or pilot light as on a
(called gasohol or using ethanol or  methanol) can attract
furnace, water heater, clothes dryer or
moisture which leads to separation and formation of acids
gasappliance. Allowtheenginetocool
before storing in any enclosure.
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
SNOW THROWER
When snow  thrower is to  be stored for a  period of time,
clean it  thoroughly,  remove all  dirt, grease,  leaves,  etc.
Store in a clean, dry area.
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
Use fresh fuel next season.
1.
Clean entire  snow thrower (See  “CLEANING” in the
Maintenance section of this manual).
NOTE:  Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow  the mix ratio found  on stabilizer container.
Run engine at  least 10 minutes after adding  stabilizer to
allow the stabilizer to reach the carburetor.Do not drain the
gas tank and carburetor if using fuel stabilizer.
2.
Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
3.
4.
Lubricate as shown in the Maintenance section of this
manual.
Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
ENGINE OIL
Drain oil  (with engine warm)  and replace with  clean en-
gine  oil. (See  “ENGINE” in  the Maintenance  section  of
this manual).
5.
Touch up  all rusted  or chipped paint  surfaces; sand
lightly before painting.
CYLINDER
ENGINE
1.
Remove spark plug.
See engine manual.
2.   Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
18
Product Specification
CategoriesPoulan Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2004
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 20 pages
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Snow Blower
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website