Poulan PP8527ESB 189539 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
1.
2.
3.
Disengage  all controls  and move  throttle  control to
STOP position. Wait for all moving parts to stop.
WARNING:  To  avoid  serious   injury,
before performing  any service  or ad-
justments:
Disconnect spark plug wire from spark plug and place
it wear it cannot come in contact with spark plug.
1.
2.
3.
Be sure throttle is in STOP position.
Remove safety ignition key.
Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
Make sure the augers and all moving
parts have completely stopped.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts  as supplied
with your snow thrower.
4.
Disconnect  spark  plug   wire  from
spark plug  and place wire  where it
cannot come in contact with plug.
4.
Connect spark plug wire to spark plug.
SNOW THROWER
TO ADJUST SNOW THROWER HEIGHT
1/4-20
LOCKNUT
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
See “TO ADJUST SKID  PLATES” and “SCRAPER BAR”
in the Operation section of this manual.
IMPELLER HUB
CHUTE DEFLECTOR
IMPELLER
SHAFT
The chute deflector, attached  to the top of the  discharge
chute, is  provided to direct  discharging snow away  from
the operator. If the deflector becomes damaged, it should
be replaced.
WARNING:  To  avoid  serious   injury,
never operate your snow thrower with
the deflector removed or damaged.
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
AUGER
HUB
SHEAR BOLTS (See Fig. 18)
AUGER SHEAR BOLTS
1/4-20
LOCKNUT
AUGER HUB
AUGER SHAFT
Both right and left-hand augers  are secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a for-
eign object or ice become lodged in the augers, the shear
bolts are  designed to  break, preventing  damage to  any
other components. If one or both augers do not turn when
auger control lever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
FIG. 18
TO REMOVE BELT COVER (See Fig. 19)
1.
Remove  the two  (2)  screws securing  belt  cover  to
frame.
1.
2.
3.
Disengage  all controls  and move  throttle  control to
STOP position. Wait for all moving parts to stop.
2.
Remove belt cover.
Replace belt cover by installing cover and screws and
tighten securely.
Disconnect spark plug wire from spark plug and place
it wear it cannot come in contact with spark plug.
Align hole in  auger hub with hole  in auger shaft and
install a  new 1/4-20  x 2" shoulder/shear  bolt. Install
BELT
COVER
1/4-20
lock nut and tighten securely.
CAUTION: Do not substitute. Use only original
equipment shear bolts  as supplied with  your
snow thrower.
4.
Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured  to the impeller shaft with two  (2)
capscrew/shear bolts and hex nuts.Should a foreign object
or ice become  lodged in the impeller, the  capscrews are
designed to break, preventing damage to any other com-
ponents.If impeller does not turn when auger control lever
is engaged, check to see if the  capscrews have sheared.
To replace the capscrew/shear bolts:
FRAME
SCREWS
16
FIG. 19
Product Specification
CategoriesPoulan Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2004
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 20 pages
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Snow Blower
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website