Hinge holds tree on stump and helps
useametalwedge. Donotattempt torestart
your saw when it is pinched or hung in a log.
control fall
Opening
of felling
cut
Use a wedge to remove pinched saw
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
Overcutting begins on the top side of the log
with the bottom of the saw against the log.
When overcutting use light downward pres-
sure.
Closing of
notch
NOTE: Before felling cut is complete, use
wedges to open the cut if necessary to
controlthedirectionoffall. Toavoidkickback
and chain damage, use wood or plastic
wedges, but never steel or iron wedges.
S Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the fell-
Overcutting
Undercutting
Undercuttinginvolves cuttingon theunder-
sideofthelogwithtopofsaw againstthelog.
When undercutting use light upward pres-
sure. Hold saw firmly and maintain control.
The saw will tend to push back toward you.
ing
cut, or movement in the upper
branches.
S As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re-
treat path.
S DO NOT cut down a partially fallen tree
withyour saw. Beextremely cautious with
partially fallen trees that may be poorly
supported. When a tree doesn’t fall com-
pletely,setthesawasideandpulldownthe
tree with a cable winch, block and tackle,
or tractor.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a fallen
tree to the desired log size.
WARNING: Never turn saw upside
down to undercut. The saw cannot be con-
trolled in this position.
Always make your first cut on the compres-
sionsideofthelog. Thecompressionsideof
the log is where the pressure of the log’s
weight is concentrated.
First cut on compression side of log
WARNING: Donot standon thelog
being cut. Any portion can roll causing loss
of footing and control. Do not stand downhill
of the log being cut.
Second cut
Second cut
IMPORTANT POINTS
S Cut only one log at a time.
S Cut shattered wood very carefully; sharp
pieces of woodcould beflung towardopera-
tor.
S Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cuttingandnever holdthelogwith your leg
or foot.
S Do not cut in an area where logs, limbs,
and roots are tangled such as in a blown
down area. Drag the logs intoa clear area
before cutting by pulling out exposed and
cleared logs first.
First cut on compression side of log
BUCKING WITHOUT A SUPPORT
S Overcut through 1/3 of the diameter of the
log.
S Roll the log over and finish with a second
overcut.
S Watch for logs with a compression side to
prevent the saw from pinching. See il-
lustrations for cutting logs with acompres-
sion side.
TYPES OF CUTTING USED FOR
BUCKING
BUCKING USING A LOG OR
SUPPORT STAND
WARNING:
If saw becomes
S Remember your first cut is always on the
compression side of the log.
pinched or hung in a log, don’t try to force it
out. Youcanlosecontrolofthesawresulting
in injury and/or damage to the saw. Stop the
saw,driveawedgeofplastic orwoodintothe
cutuntil thesaw canbe removedeasily. Re-
startthesawandcarefullyreenterthecut. To
avoid kickback and chain damage, do not
(Refer to the illustrations below for your
first and second cut)
S Your first cut should extend 1/3 of the
diameter of the log.
S Finish with your second cut.
12
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro 262 |
| Model Year | 2004 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)