8
Operating Tips
Cutting Leaves
•
After cutting the lawn, ensure that half of the lawn
shows through the cut leaf cover. You may need
to make more than one pass over the leaves.
•
•
•
Clear the area of sticks, stones, wire, branches,
and other debris that the blade could hit.
Avoid striking solid objects with the blade. Never
deliberately mow over any object.
•
If there are more than 5 inches (13 cm) of leaves
on the lawn, set the front cutting height one or
two notches higher than the rear cutting height.
If the mower strikes an object or starts to vibrate,
immediately stop the engine, disconnect the wire
from the spark plug, and examine the mower for
damage.
•
•
Slow down your mowing speed if the mower does
not cut the leaves finely enough.
If you mow over oak leaves, you can add lime to
the grass in the spring to reduce the acidity of the
leaves.
•
•
For best performance, install a new blade before
the cutting season begins.
Replace the blade when necessary with a Toro
replacement blade.
Cutting Grass
•
•
•
Cut only about a third of the grass blade at a
time. Do not cut below the 2-inch (51 mm) setting
unless the grass is sparse or it is late fall when
grass growth begins to slow down. Refer to
Adjusting the Cutting Height on page 6.
When cutting grass over 6 inches (15 cm) tall,
mow at the highest cutting height setting and walk
slower; then mow again at a lower setting for the
best lawn appearance. If the grass is too long, the
mower may plug and cause the engine to stall.
Mow only dry grass or leaves. Wet grass and
leaves tend to clump on the yard and can cause
the mower to plug or the engine to stall.
Warning
Wet grass or leaves can cause serious injury if
you slip and contact the blade. Mow only in dry
conditions.
•
Alternate the mowing direction. This helps
disperse the clippings over the lawn for even
fertilization.
If the finished lawn appearance is unsatisfactory, try
one or more of the following:
•
•
•
•
•
Replace the blade or have it sharpened.
Walk at a slower pace while mowing.
Raise the cutting height on your mower.
Cut the grass more frequently.
Overlap cutting swaths instead of cutting a full
swath with each pass.
•
Set the cutting height on the front wheels one
notch lower than the rear wheels. For example,
set the front wheels at 2 inches (51 mm) and the
rear wheels at 2-3/8 inches (60 mm).
3350-635
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro 20007 |
| Model Number | 20007 |
| Model Year | 2004 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 240000001 - 240999999 |
| Product Name | Toro 22 inch Recycler Lawnmower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Product Series | Toro 22" Steel Deck |
| Swath | 22 inch |
| Discharge | Recycler, Recycler & Rear Bagger |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 20 oz. (.6l) 30w / API SH or higher |
| Gearbox Lubricant | 1.5 oz. (43gm) #2 Lithium grease |
| Engine Motor Model # | LEV120-362003A, LV195EA-362003B |
| Engine Motor Size | 6.5 hp |
| Engine Motor Type | 4 Cycle, 4 Cycle CARB2, EPA2 |
| Transmission Speed | Infinitely Variable |
| Transmission Type | Gear |
| Spark Plug | Champion RJ19LM |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)