13
Replacing the Blade
Cleaning the Mower
Important: You will need a torque wrench to
install the blade properly. If you do not have a
torque wrench or are uncomfortable performing this
procedure, contact an Authorized Service Dealer.
1. With the engine
running on a flat paved
surface, spray a stream
of water in front of the
right rear wheel.
Examine the blade whenever you run out of gasoline.
If the blade is damaged or cracked, replace it
immediately. If the blade edge is dull or nicked, have
it sharpened or replace it.
1093
The water will splash into the path of the blade,
cleaning out the clippings.
2.
When no more clippings come out, stop the water
Warning
and move the mower to a dry area.
3.
Run the engine for a few minutes to dry the
The blade is sharp; contacting the blade can
result in serious personal injury.
housing to prevent it from rusting.
Wear cloth or leather gloves when servicing the
blade.
Storage
1.
Disconnect the spark plug wire from the spark
Store the mower in a cool, clean, dry place.
plug and hook it onto the retaining post. Refer to
Preparing for Maintenance on page 11.
2.
3.
4.
5.
Tip the mower onto its right side.
Preparing the Mower into
Storage
Use a block of wood to hold the blade steady.
Remove the blade, saving all mounting hardware.
Install the new blade and all mounting hardware.
Warning
Important: Position the curved ends of the blade to
point toward the mower.
GasolineS vapors can explode.
S
DoDo notnot storestore gasolinethe mowemorer in anthanenc30losdays.ure near
S
anAlloopenw theflame.engine to cool before storing it.
1.
On the last refueling of the year, add fuel
stabilizer to the fuel as directed by the engine
manufacturer.
2.
Run the mower until the engine stops from
running out of fuel.
3.
4.
Prime the engine and start it again.
Allow the engine to run until it stops. When you
can no longer start the engine, it is sufficiently dry.
5.
Remove the wire from the spark plug and connect
m-6216
the wire onto the retaining post.
6.
60
Use a torque wrench to tighten the blade bolt to
ft-lb (82 N⋅m).
6. Remove the spark plug, add 1 oz. (30 ml) of oil
through the spark plug hole, and pull the starter rope
slowly several times to distribute oil throughout the
cylinder to prevent cylinder corrosion during the
off-season.
Important: A bolt torqued to 60 ft-lb (82 NVm) is
very tight. While holding the blade with a block of
wood, put your weight behind the ratchet or
wrench and tighten the bolt securely. This bolt is
very difficult to overtighten.
7. Loosely install the spark plug.
8.
9.
Tighten all nuts, bolts, and screws.
Charge the battery for 72 hours, then unplug the
battery charger and store the mower in an unheated
area. If you must store the mower in a heated area,
you must charge the battery every 90 days.
3350-660
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro 20051 |
| Model Number | 20051 |
| Model Year | 2004 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 240000001-240999999 |
| Product Name | Toro 22-inch Recycler Lawnmower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Product Series | Toro 22" Steel Deck |
| Swath | 22 inch |
| Discharge | Recycler, Recycler & Rear Bagger |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 20 oz. (.6l) 30w / API SH or higher |
| Gearbox Lubricant | 1.5 oz. (43gm) #2 Lithium grease |
| Engine Motor Size | 6.75 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | Personal Pace |
| Transmission Type | Gear |
| Spark Plug | Champion RJ19LM |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)