OPERATION
TO ADJUST SKID PLATES (See Fig. 19)
NOTE:Thewrenchprovidedinyourpartsbagmaybeused
to adjust the skid plates.
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
ground surface. Adjust skid plates evenly to proper height
for current surface conditions. For removal of snow in
normal conditions, such as a paved driveway or sidewalk,
place skid plates in the highest position (lowest scraper
clearance) to give a 1/8" clearance between the scraper
bar and the ground. Use a middle position if the surface
to be cleared is uneven.
CAUTION:
Alcohol blended fuels (called
gasohol or using ethanol or methanol) can at-
tract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should be emptied before storage of
30
days or longer. Drain the gas tank, start
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. SeeStorageInstructionsforadditional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
•
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
1.
2.
Shut off engine and wait for all moving parts to stop.
CHOKE CONTROL
THROTTLE PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
Adjust skid plates by loosening the rear 1/2" hex nut
only,thenmovingskidplatetodesiredposition.Besure
both plates are adjusted evenly. Tighten securely.
SAFETY
IGNITION
KEY
HIGH POSITION
(LOW GROUND
CLEARANCE)
AUGER
HOUSING
SKID PLATE
1/2"
HEX NUT
GASOLINE
FILLER CAP
LOW POSITION (HIGH GROUND CLEARANCE)
FUEL SHUT-
OFF VALVE
FIG. 19
SCRAPER BAR
RECOIL
STARTER BUTTON
STARTER
HANDLE
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
POWER CORD PLUG
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 20
BEFORE STARTING THE ENGINE
TO START ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 20)
•
Be sure fuel shut-off valve is in the OPEN position.
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug and is
designed to operate on 120 Volt A.C. household current.
1.
2.
Check engine oil with snow thrower on level ground.
Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
•
Be sure your house is a 120 Volt A.C. three-wire
grounded system. If you are uncertain, consult a
licensed electrician.
•
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
WARNING: Do not use the electric
starter if your house is not a 120 Volt
A.C. three-wire grounded system. Se-
riouspersonalinjuryordamagetoyour
snow thrower could result.
ADD GASOLINE (See Fig. 20)
•
Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
12
| Categories | Poulan Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Poulan 961970005 |
| Model Year | 2005 |
| Download File |
|
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Snow Blower |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)