SERVICE AND ADJUSTMENTS
ENGINE
ENGINE SPEED
Nevertamperwiththeenginegovernor,whichisfactoryset
See engine manual.
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary adjustments.
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower to
a qualified service center.
STORAGE
Immediately prepare your unit for storage at the end of the
season or if the unit will not be used for 30 days or more.
•
•
•
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
WARNING: Never store the snow
throwerwithgasolineinthetankinside
a building where fumes may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gasappliance. Allowtheenginetocool
before storing in any enclosure.
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not drain the
gas tank and carburetor if using fuel stabilizer.
SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease, leaves, etc.
Store in a clean, dry area.
ENGINE OIL
Drain oil (with engine warm) and replace with clean en-
gine oil. (See “ENGINE” in the Maintenance section of
this manual).
1.
Clean entire snow thrower (See “CLEANING” in the
Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2.
Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
2.
3.
4.
Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3.
4.
Lubricate as shown in the Maintenance section of this
manual.
Pullrecoilstarterhandleslowlyafewtimestodistribute
oil.
Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
Replace with new spark plug.
5.
Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
OTHER
•
•
Do not store gasoline from one season to another.
ENGINE
See engine manual.
FUEL SYSTEM
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
•
•
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuelhose,ortankduringstorage.Also,alcoholblendedfuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
Coveryoursnowthrowerwithasuitableprotectivecover
thatdoesnotretainmoisture.Donotuseplastic.Plastic
cannotbreathe,whichallowscondensationtoformand
will cause your snow thrower to rust.
IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm.
18
Categories | Poulan Snow Blower Manuals, Snow Blower Manuals |
---|---|
Tags | Poulan PO927ES |
Model Year | 2005 |
Download File |
|
Language | English |
Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Snow Blower |
Document File Type | |
Publisher | poulan.com |
Wikipedia's Page | Poulan |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)