Computed kickback angle (CKA) Table
BAR
MODEL
P/N
Length
16″
18″
CHAIN P/N CKA without chain brake
PP3816AV
952044942
PP4218AV / PP4218AVL 952044926
952051211
952051338
33_
33_
NOTE:
If this saw is to be used for com-
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines to
be equipped with a spark arresting screen. If
you operate a chain saw in a state or locale
where such regulations exist, you are legally
mercial logging, a chain brake is required
and shall not be removed or otherwise dis-
abled tocomply withFederal OSHA Regula-
tions for Commercial Logging.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
responsible
for maintaining the operating
condition of these parts. Failure to do so is a
violation of the law. Refer to the SERVICE
section for maintenance of the spark arresting
screen. Failure to follow all Safety Rules and
Precautions can result in serious injury. If
situations occur which are not covered in this
manual, use care and good judgement. If you
need assistance, contact your authorized
service dealer or call 1-800--554--6723.
people
prone to circulation disorders or
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
damage
in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss ofstrength,changeinskincolor ortexture,
or loss offeeling inthe fingers,hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
STANDARDS: This saw is listed by Under-
writer’s Laboratories, Inc., in accordance with:
B175.1--2000 American National
for Gasoline--Powered Chain
ANSI
Standards
closely
their
physical
condition
and
the
Saws -- Safety Requirements
CSA Z62.1--03 Chain Saws -- Occupational
Health and Safety
condition of this tool.
SPECIAL NOTICE: Your saw is equipped
with a temperature limiting muffler and spark
CSA Z62.3--96 Chain Saw Kickback Occu-
pational Health and Safety
arresting
screen
which
meets
the
requirements of California Codes 4442 and
ASSEMBLY
Protective gloves (not provided) should be
3. Turnadjusting screw on bar counterclock-
wise to move thetensioning rack as far as
it will go toward the front of the bar.
worn during assembly.
ATTACHINGTHEBAR&CHAIN (Ifnot
already attached)
Adjusting
Screw
WARNING:
If received assembled,
repeat all steps to ensure your saw is properly
assembled and all fasteners are secure. Al-
ways wear gloves when handling the chain.
Thechainis sharp andcan cutyou evenwhen
it is not moving!
Tensioning Rack
1.
Loosenandremovethebar nuts andthe
clutch cover from the saw.
Remove the plastic shipping spacer (if
present).
4.
Slide guide bar on bar bolts until guide bar
stops against clutch drum sprocket.
2.
Clutch cover
Bar nuts
Location of
shipping
spacer
Bar bolts
Chain adjustment tool
(Bar Tool)
Guide bar
6
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro PP3816AV, Poulan Pro PP4218AV, Poulan Pro PP4218AVL |
| Model Year | 2005 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)