OPERATION
TO START ENGINE
Be sure fuel shut-off valve is in the OPEN position.
6. When the engine starts, release the recoil starter
handle and slowly move the choke control to the OFF
position.
•
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug and is
designed to operate on 120 Volt A.C. household current.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operating
temperature.
WARM START - RECOIL STARTER
•
Be sure your house is a 120 Volt A.C. three-wire
grounded system. If you are uncertain, consult a
licensed electrician.
Follow the steps above, keeping the choke in the OFF
position. DO NOT push the primer.
BEFORE STOPPING
WARNING: Do not use the electric
starter if your house is not a 120 Volt
A.C. three-wire grounded system. Se-
riouspersonalinjuryordamagetoyour
snow thrower could result.
Run the engine for a few minutes to help dry off any mois-
ture on the engine.
To avoid possible freeze-up of the starter, proceed as fol-
lows:
ELECTRIC STARTER
COLD START - ELECTRIC STARTER
1.
Connect the power cord to the engine.
1.
Insert safety ignition key (packed separately in parts
bag)intoignitionslotuntilitclicks. DONOTturnthekey.
Keep the extra safety ignition key in a safe place.
2. Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
2.
3.
4.
5.
Place throttle control in FAST position.
Rotate choke control to FULL position.
Connect the power cord to the engine.
3. While the engine is running, push starter button and
spin the starter for several seconds.
NOTE: The unusual sound made while starter is spinning
will not harm the engine or starter.
Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
4.
Disconnect the power cord from the receptacle first,
then from the engine.
6.
7.
Push the primer three (3) times.
RECOIL STARTER
Push starter button until engine starts.
1.
Whiletheengineisrunning,pulltherecoilstarterhandle
with rapid, full arm strokes three or four times.
IMPORTANT: Do not crank engine more than five con-
tinuous seconds between each time you try to start. Wait
NOTE: The unusual sound made while pulling the recoil
starter handle will not harm the engine or starter.
5
to 10 seconds between each attempt.
8.
When the engine starts, release the starter button and
slowly move the choke control to the “OFF” position.
IF RECOIL STARTER HAS FROZEN
9.
Disconnect the power cord from the receptacle first,
then from the engine.
If the recoil starter has frozen and will not turn the engine,
proceed as follows:
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operat-
ing temperature.
1. Grasp the recoil starter handle and slowly pull as much
rope out of the starter as possible.
2.
Release the recoil starter handle and let it snap back
against the starter.
WARM START - ELECTRIC STARTER
If the engine still fails to start, repeat the above steps or
use the electric starter.
Follow the steps above, keeping the choke control in the
OFF position.
COLD START - RECOIL STARTER
SNOW THROWING TIPS
1.
Insert safety ignition key into the ignition slot until it
clicks. DO NOT turn the key. Keep the extra safety
ignition key in a safe place.
•
•
•
•
Always operate the snow thrower with the engine at
full throttle. Full throttle offers the best performance.
Goslowerindeep,freezingorheavywetsnow.Usethe
drive speed control, NOT the throttle, to adjust speed.
2.
3.
4.
Place throttle control in FAST position.
Rotate choke control to FULL position.
It is easier and more efficient to remove snow imme-
diately after it falls.
Push the primer four (4) times if the temperature is
below 15°F, or two (2) times if temperature is between
The best time to remove snow is the early morning. At
this time the snow is usually dry and has not been ex-
posed to the direct sun and warming temperatures.
15°
and 50°F. If temperature is above 50°F, priming is
not necessary.
NOTE: Over priming may cause flooding, preventing the
engine from starting. If you do flood the engine, wait a few
minutes before attempting to start and DO NOT push the
primer.
•
Slightly overlap each successive path to ensure all
snow will be removed.
•
•
Throw snow downwind whenever possible.
Adjust the skid plates to proper height for current snow
conditions. See “TO ADJUST SKID PLATES” in this
section of this manual.
5.
Pull recoil starter handle quickly. Do not allow starter
rope to snap back.
13
| Categories | Husqvarna Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Husqvarna 10527SBE |
| Model Year | 2006, 2007, 2008 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Husqvarna, Snow Blower |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)