OPERATION
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
•
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
1.
2.
Shut off engine and wait for all moving parts to stop.
FREEWHEEL POSITION
TRANSMISSION ENGAGED
FIG. 21
Adjust skid plates by loosening the rear 1/2" hex nut
only,thenmovingskidplatetodesiredposition.Besure
both plates are adjusted evenly. Tighten securely.
BEFORE STARTING THE ENGINE
SCRAPER BAR
CHECK ENGINE OIL LEVEL (See Fig. 22)
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
1.
2.
Check engine oil with snow thrower on level ground.
Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
HIGH POSITION
(LOW GROUND
CLEARANCE)
•
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
AUGER
HOUSING
CHOKE CONTROL
THROTTLE PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
SKID PLATE
1/2"
HEX NUT
SAFETY
IGNITION
KEY
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 19
TO USE DRIFT CUTTERS (See Fig. 20)
Use the drift cutters to cut through deep snowdrifts that are
higher than the front of the snow thrower.
•
Loosen upper adjustment nut enough to allow drift
cutter to be raised to highest position and tighten nut
securely. Repeat for opposite side of snow thrower.
GASOLINE
FILLER CAP
•
When not using drift cutters, loosen adjustment nut,
lower to storage position and tighten nut securely.
FUEL SHUT-
OFF VALVE
RECOIL
STARTER
HANDLE
STARTER BUTTON
AUGER
HOUSING
POWER CORD PLUG
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
STORAGE
POSITION
DRIFT
CUTTER
FIG. 22
ADD GASOLINE (See Fig. 22)
•
Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
ADJUST-
MENT NUT
FIG. 20
TO TRANSPORT (See Fig. 21)
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
When pushing or towing your snowthrower, be sure to
disengage transmission by placing freewheel control into
FREEWHEELposition. Freewheel control is located at the
rear of snowthrower.
CAUTION: Alcohol blended fuels (called gas-
ohol or using ethanol or methanol) can attract
moisture which leads to separation and for-
mation of acids during storage. Acidic gas can
•
•
Pull freewheel control out to FREEWHEEL position.
To reengage transmission, push control back in.
12
| Categories | Husqvarna Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Husqvarna 1330SBEXP |
| Model Year | 2006, 2007, 2008 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Husqvarna, Snow Blower |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)