GB
ASSEMBLY
2. Remove the fasteners and the crank assem- How To Set The Length Of The Cables
bly eyebolt (11) from the lower holes of the
The cables were adjusted at the factory and no
adjustments should be necessary. However, af-
ter the handles are put in the operating position,
the cables can be too tight or too loose. If an
adjustment is necessary, see “How To Check
And Adjust The Cables” in the Service And Ad-
justment section.
Read and follow the assembly and adjustment
instructions for your snow thrower. All fasteners
are in the parts bag. Do not discard any parts or
material until the unit is assembled.
lower handle.
3. (Figure 1) Put the shift lever (6) into first
forward position.
(Figure 4) Raise the upper handle (2) to the
4.
5.
operating position.
WARNING: Before doing any
assembly or maintenance to the
snow thrower, remove the wire
from the spark plug.
NOTE: Make sure the cables are not
caught between the upper and lower han-
dle.
Install the fasteners and the crank assembly
eyebolt (11) that were removed in step 2.
DO NOT tighten until all fasteners are in
place.
6. (Figure 5) Attach the crank rod (15) to the
universal joint assembly (16) with the hair
pin (12).
How To Assemble The Drift Cutter
(if equipped)
Drift cutters are used to cut a path through snow
deeper than the auger housing.
1. (Figure 11) Loosen the fasteners (2) that
secure the drift cutters (1) to the auger
housing.
NOTE: In this instruction book, left and right
describe the location of a part from the oper-
ator’s position behind the unit.
2.
Raise the drift cutters (1) to the desired
NOTE: Torque is measured in foot pounds
(metric N.m). This measurement describes
how tight a nut or bolt must be. The torque is
measured with a torque wrench.
7. (Figure 4) Tighten nut on eye bolt (11).
Make sure eye bolt (11) is properly aligned
and the crank (18) can freely rotate.
height.
3. Tighten the fasteners (2).
8. Tighten all handle fasteners.
How To Prepare The Engine
NOTE: The engine was shipped from the
factory filled with oil. Check the level of the
oil. Add oil as needed.
NOTE: Fasteners and loose parts are shown
at full size in Figure 2 on page 29.
How To Install The Knob(s) (Figure 6)
NOTE: If knob(s) are already installed, go to
the next selection.
WARNING: Follow the engine
manufacturer’s instructions for the
type of fuel and oil to use. Always
NOTE: Illustrations are located on page 2
and on pages 30 through 35.
1.
Attach the knob (3) onto the speed shift le-
ver (2). On some models, the knob (3) is
attached. To lock in position, tighten the hex
jam nut (1) against the bottom of the knob
(3).
use a safety fuel container. Do not smoke
when adding gasoline to the engine. When
inside an enclosure, do not fill with gaso-
line. Before you add fuel, stop the engine.
Let the engine cool for several minutes.
Check the oil. See the engine manufacturer’s
instructions for the type of fuel and oil to use.
Before you use the unit, read the information on
safety, operation, maintenance, and storage.
Tools Required
1
1
2
2
2
1
1
Knife
Pliers
1/2 inch open end wrenches
9/16 inch open end wrenches
3/4 inch open end wrenches
Measuring tape or ruler
Screwdriver
2. Make sure the speed shift lever (2) func-
tions correctly. Move the speed shift lever
(2)
through all speeds.
How To Assemble The Chute Deflector
Important! Before You Start Operating
1.
(Figure 4) Turn the crank assembly (18)
counterclockwise until crank assembly (18)
stops.
(Figure 7) Fasten chute deflector (2) to
flange (4) with carriage bolts (1). Make sure
to install with head of the carriage bolts (1)
on the inside of the flange (2).
U
Check the fasteners. Make sure all fas-
teners are tight.
How To Remove The Snow Thrower
From The Carton
U
On electric start models, the unit was
shipped with the starter cord plugged
into the engine. Before operating, un-
plug the starter cord from the engine.
2.
1.
(Figure 3) The snow thrower is shown in the
shipping position.
2.
Cut and discard the plastic ties that secure
the crank assembly and the speed control
rod assembly.
3.
4. Tighten locknuts (6) securely.
Fasten with washers (5) and locknuts (6).
OPERATION
3.
4.
5.
6.
Cut down all four corners of the carton and
lay the side panels flat.
Locate all parts that are packed separately
and remove from the carton.
Remove and discard the packing material
from around the snow thrower.
(Figure 1) For shipping purposes, the height
adjust skids (7) are attached to the pallet.
Remove the screw (17) that secures each
height adjust skid (7) to the pallet.
Hold onto the lower handle and pull the snow
thrower off the pallet.
CAUTION: DO NOT back over cables.
Remove the packing material from the han-
dle assembly.
Cut the ties that secure the clutch control
cables (1) to the lower handle (2). Move the
cables away from the motor frame.
NOTE: Illustrations are located on page 2
and on pages 30 through 35.
CAUTION: Use only attachments and acces-
sories approved by the manufacturer of the
snow thrower (such as tire chains, electric
start kits, etc.).
NOTE: Make sure all carriage bolts in flange
are tight. DO NOT OVERTIGHTEN.
Check The Cables
1.
(Figure 8) Check the traction drive cable
(1) and the auger drive cable (2). If the bot-
Know Your Snow Thrower (Figure 1)
tom of the cables have become discon-
nected, reinstall the cables.
Read this Instruction Book and safety rules be-
fore operation the snow thrower. Compare the
illustration with your snow thrower to familiarize
yourself with the location of various controls and
adjustments.
7.
2.
(Figure 10) If the top of the cables (5) have
become disconnected from the drive levers
8.
9.
(6)
, attach the cables (5) to the “Z” fitting
(7).
How To Control
The Discharge Of The Snow
How To Set The Skid Height (Figure 1)
WARNING: Never direct the dis-
charge of snow toward bystanders.
The snow thrower is equipped with height ad-
justable skids (7) mounted on the outside of the
auger housing (4). To adjust the height of the
skids, see “How To Adjust The Height Of The
Skids” in the Maintenance section.
How To Assemble The Handle And
Crank Assembly
1.
WARNING: Always stop the engine
before unclogging the discharge
chute or the auger housing and be-
fore leaving the snow thrower.
(Figure 4) Loosen, but do not remove, the
fasteners (1) in the upper holes of the lower
handle.
7
| Categories | Poulan Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Poulan 5.5HP, Poulan 96194000200 |
| Download File |
|
| Language | English, Español |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Snow Blower |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)