Computed kickback angle (CKA) Table
BAR
MODEL
295
P/N
Length
CHAIN P/N
952051310
CKA without chain brake
952044815
20″
31_
NOTE: Ifthissaw istobeusedforcommer-
cial logging, a chain brake is required and
shall not be removed or otherwise disabled
to comply with Federal OSHA Regulations
for Commercial Logging.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines
tobeequippedwithaspark arrestingscreen.
Ifyouoperateachainsaw inastate or locale
wheresuchregulations exist,you arelegally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
people
prone to circulation disorders or
section
for maintenance of the spark
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
arresting screen.
damage
in
otherwise
healthy
people.
If
FailuretofollowallSafetyRules andPrecau-
tions canresult inserious injury. Ifsituations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your authorized service
dealer or call 1-800--554--6723.
symptoms occur such as numbness, pain,
loss ofstrength,changeinskincolor ortexture,
or loss offeeling inthe fingers,hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
STANDARDS: This saw is listed by Under-
writer’s Laboratories, Inc., in accordance with:
B175.1--2000 American National
for Gasoline--Powered Chain
ANSI
closely
their
physical
condition
and
the
Standards
condition of this tool.
Saws -- Safety Requirements
SPECIALNOTICE:Yoursaw isequipped
CSA Z62.1--1995 Chain Saws -- Occupa-
tional Health and Safety
with a temperature limiting muffler andspark
arresting
screen
which
meets
the
CSA Z62.3--1996 Chain Saw Kickback Oc-
cupational Health and Safety
requirements of California Codes 4442 and
ASSEMBLY
Protective gloves (not provided) should be
worn during assembly.
Location of shipping spacer
ATTACHING THE BUMPER
SPIKE (If not already attached)
The bumper spike may be used as a pivot
when making a cut.
1.
Loosenandremovethechainbrakenuts
and the chain brake from the saw.
Attach the bumper spike with the two
screws as illustrated.
2.
Chain Brake
Nuts
Chain Brake
Bar Tool
3.
Turn adjusting screw on bar counter-
clockwisetomovethetensioningrackas
far as it will go towardthe frontof thebar.
ATTACHINGTHEBAR&CHAIN (Ifnot
already attached)
WARNING: If received assembled,
repeat all steps to ensure your saw is prop-
erly assembledand allfasteners aresecure.
Always wear gloves when handling the
chain. The chain is sharp and can cut you
even when it is not moving!
Adjusting
Screw
1.
Loosenandremovethechainbrakenuts
and the chain brake from the saw.
Remove the plastic shipping spacer (if
present).
Tensioning Rack
2.
4.
Slidethebar behind clutchdrum untilbar
stops against clutch drum sprocket.
6
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro 295 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)