OPERATION
ground surface. Adjust skid plates evenly to proper height
1. Check engine oil with snow thrower on level ground.
for current surface conditions. For removal of snow in
normal conditions, such as a paved driveway or sidewalk,
place skid plates in the highest position (lowest scraper
clearance) to give a 1/8" clearance between the scraper
bar and the ground. Use a middle position if the surface
to be cleared is uneven.
2.
Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
•
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
ADD GASOLINE (See Fig. 21)
•
Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
•
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
1.
2.
Shut off engine and wait for all moving parts to stop.
Adjust skid plates by loosening the rear 1/2" hex nut
only,thenmovingskidplatetodesiredposition.Besure
both plates are adjusted evenly. Tighten securely.
CAUTION:
Alcohol blended fuels (called
gasohol or using ethanol or methanol) can at-
tract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should be emptied before storage of
HIGH POSITION
(LOW GROUND
CLEARANCE)
AUGER
HOUSING
30
days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. SeeStorageInstructionsforadditional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
SKID PLATE
1/2"
HEX NUT
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 19
SCRAPER BAR
CHOKE CONTROL
THROTTLE PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
SAFETY
IGNITION
KEY
TO USE DRIFT CUTTERS (See Fig. 20)
Use the drift cutters to cut through deep snowdrifts that are
higher than the front of the snow thrower.
•
Loosen upper adjustment nut enough to allow drift
cutter to be raised to highest position and tighten nut
securely. Repeat for opposite side of snow thrower.
•
When not using drift cutters, loosen adjustment nut,
lower to storage position and tighten nut securely.
GASOLINE
FILLER CAP
AUGER
HOUSING
FUEL SHUT-
OFF VALVE
RECOIL
STARTER
HANDLE
STARTER BUTTON
STORAGE
POSITION
DRIFT
CUTTER
POWER CORD PLUG
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
ADJUST-
MENT NUT
FIG. 21
TO START ENGINE
Be sure fuel shut-off valve is in the OPEN position.
FIG. 20
BEFORE STARTING THE ENGINE
•
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug and is
designed to operate on 120 Volt A.C. household current.
CHECK ENGINE OIL LEVEL (See Fig. 21)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
12
| Categories | Poulan Pro Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Poulan Pro PP1130ES |
| Model Year | 2006 |
| Download File |
|
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)