OPERATION
1. Shut off engine and wait for all moving parts to stop.
BEFORE STARTING THE ENGINE
2.
Adjust skid plates by loosening the rear 1/2" hex nut
only,thenmovingskidplatetodesiredposition.Besure
both plates are adjusted evenly. Tighten securely.
CHECK ENGINE OIL LEVEL (See Fig. 22)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
1.
Check engine oil with snow thrower on level ground.
HIGH POSITION
LOW GROUND
CLEARANCE)
2. Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
(
AUGER
HOUSING
•
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
SKID PLATE
ADD GASOLINE (See Fig. 22)
1/2"
HEX NUT
•
Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 19
SCRAPER BAR
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
CAUTION:
Alcohol blended fuels (called
gasohol or using ethanol or methanol) can at-
tract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should be emptied before storage of
TO USE DRIFT CUTTERS (See Fig. 20)
Use the drift cutters to cut through deep snowdrifts that are
higher than the front of the snow thrower.
•
Loosen upper adjustment nut enough to allow drift
cutter to be raised to highest position and tighten nut
securely. Repeat for opposite side of snow thrower.
30
days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. SeeStorageInstructionsforadditional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
•
When not using drift cutters, loosen adjustment nut,
lower to storage position and tighten nut securely.
AUGER
HOUSING
CHOKE
CONTROL
THROTTLE PRIMER ENGINE OIL
FILL CAP /
DIPSTICK
STORAGE
POSITION
DRIFT
CUTTER
SAFETY
IGNITION
KEY
ADJUST-
MENT NUT
FIG. 20
TO TRANSPORT (See Fig. 21)
When pushing or towing your snowthrower, be sure to
disengage transmission by placing freewheel control into
FREEWHEELposition. Freewheel control is located at the
rear of snowthrower.
GASOLINE
FILLER CAP
FUEL SHUT-
OFF VALVE
•
•
Pull freewheel control out to FREEWHEEL position.
To reengage transmission, push control back in.
RECOIL
STARTER
HANDLE
STARTER BUTTON
POWER CORD PLUG
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 22
TO START ENGINE
•
Be sure fuel shut-off valve is in the OPEN position.
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug and is
designed to operate on 120 Volt A.C. household current.
FREEWHEEL POSITION
TRANSMISSION ENGAGED
FIG. 21
12
| Categories | Poulan Pro Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Poulan Pro PP11H30ES |
| Model Year | 2006 |
| Download File |
|
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)