Poulan Pro PP8527ES 401214 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
WARNING: To avoid serious injury, before performing any service or adjustments:
1.
2.
3.
4.
Be sure throttle is in STOP position.
Remove safety ignition key.
Make sure the augers and all moving parts have completely stopped.
Disconnect spark plug wire from spark plug and place wire where it cannot contact plug.
SNOW THROWER
TO ADJUST SNOW THROWER HEIGHT
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts  as supplied
with your snow thrower.
See “TO ADJUST SKID PLATES” and  “SCRAPER BAR”
in the Operation section of this manual.
4.
Connect spark plug wire to spark plug.
CHUTE DEFLECTOR
The chute deflector, attached  to the top of the  discharge
chute, is provided  to direct discharging  snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
1
LOCKNUT
/4-20
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
IMPELLER HUB
IMPELLER
SHAFT
WARNING:  To  avoid  serious   injury,
never operate your snow thrower with
the deflector removed or damaged.
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
SHEAR BOLTS (See Fig. 19)
AUGER
HUB
AUGER SHEAR BOLTS
Both right and left-hand augers are  secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a for-
eign object or ice become lodged in the augers, the shear
bolts are  designed to  break, preventing  damage to  any
other components. If one or both augers do not turn when
auger control lever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
1/4-20
LOCKNUT
AUGER HUB
FIG. 19
AUGER SHAFT
TO REMOVE BELT COVER (See Fig. 20)
Remove the two screws securing belt cover to frame.
Remove belt cover.
1.
2.
1.
2.
3.
Disengage  all controls  and move  throttle  control to
STOP position. Wait for all moving parts to stop.
Replace belt cover by installing cover and screws and
tighten securely.
Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
Align hole in  auger hub with hole  in auger shaft and
install a  new 1/4-20 x  2" shoulder/shear  bolt. Install
1/4-20
lock nut and tighten securely.
CAUTION: Do not substitute. Use only original
equipment shear bolts  as supplied with your
snow thrower.
4.
Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
FRAME
BELT COVER
FIG. 20
SCREWS
The impeller is secured  to the impeller shaft with two  (2)
capscrew/shearboltsandhexnuts.Shouldaforeignobject
or ice become  lodged in the impeller, the  capscrews are
designed to break, preventing damage to any other com-
ponents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear bolts:
TO REPLACE BELTS (See Fig. 21)
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced. It is recommended that the belt(s) be replaced
by a qualified service center.
1.
2.
3.
Disengage  all controls  and move  throttle  control to
STOP position. Wait for all moving parts to stop.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Usingother
than OEM belts  can cause personal injury or  damage to
the snow thrower.
Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
15
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2006
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 20 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website