S Turn idle speed screw (T) counterclock-
wise to decrease engine speed.
1.
2.
3.
4.
Loosen 3 screws on cylinder cover.
Remove the cylinder cover.
If you require further assistance or are unsure
about performing this procedure, contact your
call
Pull off the spark plug boot.
Remove spark plug from cylinder and dis-
card.
Replace with Champion RCJ--7Y spark
plug and tighten securely with a 3/4 inch
authorized
service
dealer
or
1--800--554--6723.
5.
BAR MAINTENANCE
(19
mm) socket wrench. Spark plug gap
If your saw cuts to one side, has to be forced
through the cut, or been run with an improper
amount of bar lubrication it may be necessary
to service your bar. A worn bar will damage
your chain and make cutting difficult.
After each use, ensure ON/STOP switch is in
theSTOPposition,thencleanallsawdust from
the guide bar and sprocket hole.
should be 0.025 inch (0.6 mm).
Reinstall the spark plug boot.
Reinstall the cylinder cover and 3 screws.
Tighten securely.
6.
7.
Screws
Cylinder
Cover
Spark
Plug Boot
To maintain guide bar:
S Move ON/STOP switch to the STOP posi-
tion.
Spark
Plug
S Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from
saw.
STORAGE
S Cleantheoilholes andbargrooveaftereach
5
hours of operation.
WARNING:
Stop engine and allow
to cool, and secure the unit before storing or
transporting in a vehicle. Store unit and fuel
in an area where fuel vapors cannot reach
sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.
Storeunitwithallguards inplace.Positionso
that any sharp object cannot accidentally
cause injury to passersby. Store the unit out
of reach of children.
Remove Sawdust From
Guide Bar Groove
Oil Holes
S Burringofguidebar rails is a normalprocess
of rail wear. Remove these burrs with a flat
file.
S When rail top is uneven, use a flat file to re-
store square edges and sides.
File Rail Edges
and Sides
Square
S
Before storing, drain all fuel from the unit.
Start engine and allow to run until it stops.
S Clean the unit before storing. Pay particu-
lar attention to the air intake area, keeping
it free of debris. Use a mild detergent and
sponge to clean the plastic surfaces.
S Donotstoretheunitorfuelinaclosedarea
where fuel vapors can reach sparks or an
openflamefromhotwater heaters,electric
motors or switches, furnaces, etc.
Worn Groove
Correct Groove
Store in a dry area out of the reach of chil-
dren.
Replace guide bar when the groove is worn,
theguidebar is bentor cracked,or whenexce-
ss heating or burring of the rails occurs. If re-
placementis necessary,useonlytheguidebar
specified for your saw in the repair parts list or
on the decal located on the chain saw.
S
CAUTION:
It is important to prevent gum
deposits from forming in essential fuel system
parts such as the carburetor, fuel filter, fuel
hose, or fuel tank during storage. Alcohol
blended fuels (called gasohol or using ethanol
or methanol) can attract moisture which leads
to fuel mixture separation and formation of
acids during storage. Acidic gas can damage
the engine.
CHAIN SHARPENING
Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpening to a professional
chain sharpener.
IGNITION TIMING
Ignition timing is fixed and nonadjustable.
NEED ASSISTANCE?
SPARK PLUG
The spark plug should be replaced each
year to ensure the engine starts easier and
runs better.
NEED ASSISTANCE?
Call 1--800--554--6723.
NEED SERVICE PART?
Contact your authorized service dealer.
15
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro SM4018 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)