Computed kickback angle (CKA) Table
BAR
MODEL
P/N
Length
CHAIN P/N
952051338
CKA without chain brake
33_
SM4218 AV
952044926
18″
NOTE:
If this saw is to be used for com-
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines
tobeequippedwithaspark arrestingscreen.
Ifyouoperateachainsaw inastate or locale
wheresuchregulations exist,you arelegally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
mercial logging, a chain brake is required
and shall not be removed or otherwise dis-
abled tocomply withFederal OSHA Regula-
tions for Commercial Logging.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people
prone to circulation disorders or
section
for maintenance of the spark
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
arresting screen.
FailuretofollowallSafetyRules andPrecau-
tions canresult inserious injury. Ifsituations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your authorized service
dealer or call 1-800--554--6723.
damage
in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss ofstrength,changeinskincolor ortexture,
or loss offeeling inthe fingers,hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
STANDARDS: This saw is listed by Under-
writer’s Laboratories, Inc., in accordance with:
B175.1--2000 American National
for Gasoline--Powered Chain
ANSI
closely
their
physical
condition
and
the
Standards
condition of this tool.
Saws -- Safety Requirements
CSA Z62.1--03 Chain Saws -- Occupational
Health and Safety
SPECIALNOTICE:Yoursaw isequipped
with a temperature limiting muffler andspark
arresting
screen
which
meets
the
CSA Z62.3--96 Chain Saw Kickback Occu-
pational Health and Safety
requirements of California Codes 4442 and
ASSEMBLY
Protective gloves (not provided) should be
worn during assembly.
ATTACHINGTHEBAR&CHAIN (Ifnot
already attached)
3.
Turnadjusting screw on bar counterclock-
wise to move thetensioning rack as far as
it will go toward the front of the bar.
Adjusting
Screw
WARNING:
If received assembled,
repeat all steps to ensure your saw is properly
assembled and all fasteners are secure. Al-
ways wear gloves when handling the chain.
Thechainis sharp andcan cutyou evenwhen
it is not moving!
Tensioning Rack
1.
Loosenandremovethebar nuts andthe
clutch cover from the saw.
Remove the plastic shipping spacer (if
present).
4.
Slide guide bar on bar bolts until guide bar
stops against clutch drum sprocket.
2.
Clutch cover
Bar bolts
Bar nuts
Location of
shipping
spacer
Guide bar
5.
Carefully remove the chainfrom thepack-
age. Hold chain with the drive links as
shown.
Chain adjustment tool
(Bar Tool)
6
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro SM4218 AV |
| Model Year | 2006 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)