11
Changing the Engine Oil
Replacing the Blade
Change the engine oil after the first 2 operating
Important: You will need a torque wrench to
install the blade properly. If you do not have a
torque wrench or are uncomfortable performing this
procedure, contact an Authorized Service Dealer.
hours; change it yearly thereafter.
Run the engine a few minutes before changing the oil
to warm it. Warm oil flows better and carries more
contaminants.
Examine the blade whenever you run out of gasoline.
If the blade is damaged or cracked, replace it
immediately. If the blade edge is dull or nicked, have
it sharpened or replace it.
Refer to Preparing for Maintenance on page 10.
1.
Remove the
dipstick.
Warning
The blade is sharp; contacting the blade can
result in serious personal injury.
m-5604
2.
Tip the mower onto
Wear cloth or leather gloves when servicing the
blade.
its right side to drain the
used oil out through the
oil fill tube.
1.
Disconnect the spark plug wire from the spark
plug and hook it onto the retaining post. Refer to
Preparing for Maintenance on page 10.
2.
3.
4.
5.
Tip the mower onto its side (with the air filter up).
Use a block of wood to hold the blade steady.
Remove the blade, saving all mounting hardware.
Install the new blade and all mounting hardware.
m-5590
3.
Slowly pour oil into
the oil fill tube until the
oil level reaches the Full
line on the dipstick. Do
not overfill. (Max. fill:
Important: Position the curved ends of the blade to
point toward the mower.
20
oz., type: SAE 30W
detergent oil with an API
service classification of
SF, SG, SH, SJ, SL, or
higher.)
m-5571
4.
5.
Install the dipstick securely.
Dispose of the used oil properly at a local
recycling center.
Lubricating the Wheel
Gears
1.
Remove the wheel bolts on the front wheels and
remove the front wheels.
2.
Apply a lubricating
oil to the inner and outer
sides of the gear as
shown.
m-6216
6.
60
Use a torque wrench to tighten the blade bolt to
ft-lb (82 N⋅m).
m-5647
3.
Install the front wheels.
Important: A bolt torqued to 60 ft-lb (82 NVm) is
very tight. While holding the blade with a block of
wood, put your weight behind the ratchet or
wrench and tighten the bolt securely. This bolt is
very difficult to overtighten.
3352-550
Rev A
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro 20005 |
| Model Number | 20005 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 260000001-260999999 |
| Product Name | Toro 22-inch Recycler Lawnmower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Product Type | Walk Behind Mower |
| Product Series | Toro 22" Steel Deck |
| Swath | 22 inch |
| Discharge | Recycler, Recycler & Rear Bagger |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 20 oz. (.6l) 30w / API SH or higher |
| Gearbox Lubricant | 1.5 oz. (43gm) #2 Lithium grease |
| Engine Motor Model # | LV195EA-362003D |
| Engine Motor Size | 6.5 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | Infinitely Variable |
| Transmission Type | Gear |
| Spark Plug | Champion RJ19LM |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)