Form No. 3353-603 Rev B
PowerMax Snowthrower
Model No. 38622
Setup Instructions
Important: Refer to your Operator’s Manual for safety,
maintenance, and warranty information.
9.
Secure the trunnion and upper end of the speed control
rod with the outer washer and a hairpin cotter.
Setup
Note: For easier
installation, look down
1.
Position the upper handle over the lower handle.
through the opening in the
speed selector (H).
H
Note: Do not remove
the rubber band until
you have installed the
handle.
m-6972
10.
Unwrap the Quick Stick and rotate it so that it is upright
and in the center.
A
Important: Route the
11.
Hold the blue cap down and pull the lever fully back.
2
cables attached to the
Note: The discharge chute and deflector should face
forward. If they do not, hold the blue cap down (but do not
move the Quick Stick), and rotate the discharge chute until
they do.
Quick Stick (A) inside
the upper handle legs.
Do not pinch the cables
or the headlight wire.
m-7698
12. Align the flattened end of the long rod (I) with the flattened
end of the short rod (J) that extends from the control panel so
they nest together.
2.
3.
Secure the upper handle (fasteners are shown above).
Remove the hairpin
cotter and washer from the
end of the speed control rod
(B) and insert the end into the
lower link arm (C).
B
C
m–6973
I
4.
Secure the rod end with
the washer and hairpin cotter.
J
m-6899
m-6969
5.
Remove the hairpin cotter and the outer washer from the
trunnion (D) on the upper end of the speed control rod.
13. Insert the long rod
end into the back of the
chute gear cover until it
slides into the gear.
G E
D
14.
Align the holes in the nested ends of the rods and insert 2
bolts through the short rod from the left side (from the
operating position).
F
15.
Insert the cable clip (K)
M
that supports the deflector
cable (L) on the forward bolt
(M), and secure the bolts with
the locknuts provided.
m-6898a
Note: Do not remove the wave washer (E) or the flat
washer (F).
L
6.
selector lever into
Position R2.
Shift the speed
K
16.
Hold the blue cap down and rotate the Quick Stick in a
circle to ensure that the chute and deflector work smoothly.
7.
link arm up.
Rotate the lower
17.
Insert the wire connector
m–6971
on the loose end of the wire
straight into the back of the
headlight.
8.
hole in the speed selector lever (see G above) located under
the control panel.
Lift up the speed control rod and insert the trunnion in the
18.
Secure a cable tie
around the wire and the
handle about an inch (2.5 cm)
below the U-bolt.
Note: If the trunnion does not fit into the hole when you lift
up the speed control rod, rotate the trunnion up or down on
the speed control rod until it fits.
m-7011
2005 by The Toro Company
Lyndale Ave., Bloomington, MN 55420, USA
Printed in the USA
All Rights Reserved
Original Instructions (EN)
Register your product at www.toro.com
E
8111
Categories | Snow Blower Manuals, Toro Snow Blower |
---|---|
Tags | Toro 38622, Toro Power Max 828LE |
Model Number | 38622 |
Model Year | 2006 |
Download File |
|
Document Type | Setup Instructions |
Language | English |
Serial Number | 260000001 - 260999999 |
Product Name | Toro Power Max 826 LE Snowthrower |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
Product Type | Snowthrower |
Product Series | Snowthrower, Two Stage Power Max |
Swath | 26 inch |
Discharge | Two Stage |
Engine Manufacturer | Tecumseh |
Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
Engine Motor Model # | LH318SA-156563H |
Engine Motor Size | 318cc |
Engine Motor Type | 4 Cycle CARB2, EPA2 |
Transmission Speed | 6 Forward/2 Reverse |
Transmission Type | Friction Disc |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)