GB
2. (Figure 11) If the top of the cables (5) have
become disconnected from the drive levers
(6), attach the cables (5) to the “Z” fitting
ASSEMBLY
NOTE: Make sure the cables are not
caught between the upper and lower han-
dle.
5. Install the fasteners and the crank assembly
eyebolt (11) that were removed DO NOT
tighten until all fasteners are in place.
Read and follow the assembly and adjustment
instructions for your snow thrower. All fasteners
are in the parts bag. Do not discard any parts or
material until the unit is assembled.
(7).
How To Set The Skid Height (Figure 1)
6.
(Figure 6) Attach the crank rod (15) to the
universal joint assembly (16) with the hair
pin (12).
The snow thrower is equipped with height ad-
justable skids (7) mounted on the outside of the
auger housing (4). To adjust the height of the
skids, see “How To Adjust The Height Of The
Skids” in the Maintenance section.
WARNING: Before doing any as-
sembly or maintenance to the snow
thrower, remove the wire from the
spark plug.
7. (Figure 4) Tighten nut on eye bolt (11).
Make sure eye bolt (11) is properly aligned
and the crank (18) can freely rotate.
NOTE: In this instruction book, left and right
describe the location of a part from the oper-
ator’s position behind the unit.
8.
Tighten all handle fasteners.
How To Set The Length Of The Cables
The cables were adjusted at the factory and no
adjustments should be necessary. However, af-
ter the handles are put in the operating position,
the cables can be too tight or too loose. If an
adjustment is necessary, see “How To Check
And Adjust The Cables” in the Service And Ad-
justment section.
NOTE: Torque is measured in foot pounds
(metric N.m). This measurement describes
how tight a nut or bolt must be. The torque is
measured with a torque wrench.
How To Install The Speed Control Rod
1.
(Figure 9) Attach the ball joint (6), located
on the bottom end of the speed control rod
(2), to the shift yoke assembly (7). The fas-
teners (8) are attached to the ball joint (6)
at the factory.
NOTE: Fasteners and loose parts are shown
at full size in Figure 31 on page 35.
NOTE: Illustrations are located on page 2
and on pages 29 through 34.
The length of the ball joint (6) and speed
control rod (2) have been pre--adjusted at
the factory. If an adjustment is required, loos-
en the nut (9). Remove the fasteners (8) to
disconnect the ball joint (6) from the shift
yoke assembly (7). To lengthen or shorten
the speed control rod (2), turn the adapter
How To Assemble The Drift Cutter
(if equipped)
Drift cutters are used to cut a path through snow
deeper than the auger housing.
Tools Required
1
1
2
2
2
1
1
Knife
Pliers
1.
Loosen the wingnuts (2) that secure the
drift cutters (1) to the auger housing.
1/2 inch open end wrenches
9/16 inch open end wrenches
3/4 inch open end wrenches
Measuring tape or ruler
Screwdriver
(10)
to obtain the correct length.
2. Raise the drift cutters (1) to the desired
height.
2.
Attach the handle (11) onto the speed se-
lect lever (5). On some models the handle
3.
Tighten the wingnuts (2).
(11)
is attached. To lock in position, tighten
the hex jam nut (10) against the bottom of
the handle (11).
3. Make sure the speed select lever (5) func-
tions correctly. Move the speed select lever
How To Prepare The Engine
NOTE: The engine was shipped from the
factory filled with oil. Check the level of the
oil. Add oil as needed.
How To Remove The Snow Thrower
From The Carton
(5)
through all speeds.
1.
(Figure 3) The snow thrower is shown in the
shipping position.
WARNING: Follow the engine
manufacturer’s instructions for the
type of fuel and oil to use. Always
use a safety fuel container. Do not smoke
when adding gasoline to the engine. When
inside an enclosure, do not fill with gaso-
line. Before you add fuel, stop the engine.
Let the engine cool for several minutes.
2.
Cut and discard the plastic ties that secure
the crank assembly and the speed control
rod assembly.
How To Install The Knobs
NOTE: If knobs are already installed, go to
the next selection.
3.
4.
5.
6.
Cut down all four corners of the carton and
lay the side panels flat.
Locate all parts that are packed separately
and remove from the carton.
Remove and discard the packing material
from around the snow thrower.
(Figure 1) For shipping purposes, the height
adjust skids (7) are attached to the pallet.
Remove the screw (17) that secures each
height adjust skid (7) to the pallet.
Remote Chute Knob
Check the oil. See the engine manufacturer’s
instructions for the type of fuel and oil to use.
Before you use the unit, read the information on
safety, operation, maintenance, and storage.
1.
Assemble remote chute knob (1) onto lever
(3) until snug against nut (2). On some mod-
els the remote chute knob (1) is attached.
2.
3.
Make sure lip (4) on the remote chute knob
(1)
is pointed toward the engine.
Tighten the nut (2) against the bottom of the
remote chute knob (1).
Important! Before You Start Operating
7.
Hold onto the lower handle and pull the snow
thrower off the pallet.
U
Check the fasteners. Make sure all fas-
teners are tight.
CAUTION: DO NOT back over cables.
Remove the packing material from the han-
dle assembly.
Cut the ties that secure the clutch control
cables (1) to the lower handle (2). Move the
cables away from the motor frame.
How To Assemble The Chute Deflector
1. (Figure 7) Remove carriage bolt (1).
2. Raise the chute deflector (2) into operating
position (3).
On electric start models, the unit was
shipped with the starter cord plugged
into the engine. Before operating, un-
plug the starter cord from the engine.
U
8.
9.
3.
Fasten chute deflector (2) to flange (4) with
carriage bolts (1). Make sure to install with
head of the carriage bolts (1) on the inside
of the flange (2).
U
If a bar code label is attached to the han-
dle, remove before operating.
How To Assemble The Handle And
Crank Assembly
(Figure 4) Loosen, but do not remove, the
fasteners (1) in the upper holes of the lower
handle.
Remove the fasteners and the crank assem-
bly eyebolt (11) from the lower holes of the
lower handle.
OPERATION
4. Fasten with washers (5) and locknuts (6).
5. Tighten locknuts (6) securely.
NOTE: Illustrations are located on page 2
and on pages 29 through 34.
CAUTION: Use only attachments and acces-
sories approved by the manufacturer of the
snow thrower (such as tire chains, electric
start kits, etc.).
1.
NOTE: Make sure all carriage bolts in flange
are tight. DO NOT OVERTIGHTEN.
2.
Check The Cables
3.
4.
(Figure 1) Put the shift lever (6) into first
forward position.
(Figure 4) Raise the upper handle (2) to the
operating position.
1. (Figure 8) Check the traction drive cable
(1) and the auger drive cable (2). If the bot-
tom of the cables have become discon-
nected, reinstall the cables.
Know Your Snow Thrower (Figure 1)
Read this Instruction Book and safety rules be-
fore operation the snow thrower. Compare the
7
| Categories | Poulan Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Poulan 96194000300 |
| Model Year | 2007 |
| Download File |
|
| Language | English, Español |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Snow Blower |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)