Poulan Pro 96192001902 416804 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
10.
11. Placeaugerbeltaroundandinsidethegrooveofauger
pulley only.
12.
13.
Install clutch rod in swing plate; secure with hairpin.
be replaced. It is recommended that the belt(s) be replaced
by a qualified service center.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
While your  assistant slowly  raises handles  to rejoin
the auger housing and frame assembly, pull up on the
auger belt and  squeeze sides together above  pulley
so belt is fully seated in groove of pulley.
Bring snow  thrower  completely together  and check
carefully for proper routing of belts.  If  auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket  while  bringing snow  thrower together),
separate the snow thrower  and repeat step 12.  Belt
must be  fully seated in  pulley groove when bringing
the snow thrower together.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Usingother
than OEM belts  can cause personal injury or  damage to
the snow thrower.
WARNING: Belt replacement  requires
separation of the snow thrower. While
separating the auger housing from the
frame  assembly,  it  is important  that
an  assistant  stand  in  the  operating
position  and  hold the  snow  thrower
handles.Seriouspersonalinjuryand/or
damage to the  unit could occur if  the
snowthrowershouldfallduringthebelt
changing process.
14.
Install the two (2) hex bolts and tighten securely.
15. INSTALLENGINEPULLEY-Placebeltinpulleygroove
and  slide pulley  on  crankshaft.   Install  flat washer,
lockwasher and bolt and tighten securely (41-47 N-m
torque).  Make sure belt is inside belt keeper.
16.
INSTALL BELT COVER and  two (2) screws. Tighten
securely.
INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
FRAME
ASSEMBLY
AUGER
HOUSING
17.
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
HANDLES
FLAT WASHER
PULLEY
1
.   REMOVE  GASOLINE  FROM  FUEL  TANK  -  Drain
gasoline from fuel tank into  a suitable container, out-
doors, away  from fire or  flame. Wipe  up any spilled
gasoline.
LOCKWASHER
BOLT
2.
REMOVE  DISCHARGE  CHUTE  -  Loosen  locknut
securing chute rotator head to mounting bracket only
enough to allow  chute rotator head to be  raised and
discharge chute to be removed from snow thrower.
REMOVE BELT COVER  - See “TO  REMOVE BELT
COVER” in this section of this manual.
IDLER ARM
SQUARE
HOLE
AUGER
BELT
CLUTCHING
IDLER ARM
BRACKET
3.
4
.   REMOVEENGINEPULLEY-Removebolt,lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
removethetwo(2)boltsholdingtheaugerhousingand
frame together.
AUGER
HOUSING
FRAME
AUGER PULLEY
BOLTS
5.
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
FIG. 24
6.
7.
REMOVEHAIRPINFROMCLUTCHRODandremove
clutch rod from swing plate.  Tip swing plate forward.
REMOVE AUGER BELT from around pulley.
TO REMOVE WHEELS (See Fig. 25)
Remove the klik pin and remove wheel from axle.
8
.   RELIEVETENSIONONTRACTIONDRIVEBELTIDLER
IMPORTANT: When installing  wheel, be sure  to use the
axle hole closest to the end  of the shaft – do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
holeinwheelhubarenotusedforyourmodelsnowthrower.
and remove  traction drive  belt from  around pulleys.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in  idler arm and rotate ratchet clockwise
to relieve tension.
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
9.
With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
17
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2007
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website