Poulan Pro 961980018 415312 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
12.
Install the two (2) hex bolts and tighten securely.
WARNING: Belt replacement  requires
separation of the snow thrower. While
separating the auger housing from the
frame  assembly,  it  is important  that
an  assistant  stand  in  the  operating
position  and  hold the  snow  thrower
handles.Seriouspersonalinjuryand/or
damage to the  unit could occur if  the
snowthrowershouldfallduringthebelt
changing process.
13. INSTALLENGINEPULLEY-Placebeltinpulleygroove
and  slide pulley  on  crankshaft.   Install  flat washer,
lockwasher and  bolt  and tighten  securely (30-35  ft.
lbs. torque).  Make sure belt is inside belt keeper.
14.
INSTALL BELT COVER and  two (2) screws. Tighten
securely.
INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
15.
FRAME
AUGER
HOUSING
ASSEMBLY
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
FLAT WASHER
PULLEY
LOCKWASHER
BOLT
HANDLES
1.
2.
REMOVE  GASOLINE  FROM  FUEL TANK  -  Drain
gasoline from fuel tank into  a suitable container, out-
doors, away  from fire or  flame. Wipe  up any spilled
gasoline.
REMOVE  DISCHARGE  CHUTE  -  Loosen  locknut
securing chute rotator head to mounting bracket only
enough to allow  chute rotator head to be  raised and
discharge chute to be removed from snow thrower.
IDLER ARM
SQUARE
HOLE
AUGER
BELT
CLUTCHING
IDLER ARM
BRACKET
AUGER PULLEY
3.
4.
REMOVE BELT COVER  - See “TO  REMOVE BELT
COVER” in this section of this manual.
REMOVEENGINEPULLEY-Removebolt,lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
BOLT
5.
SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two  (2) bolts holding  auger housing and
frame together.
AUGER
HOUSING
FRAME
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
FIG. 21
TO REMOVE WHEELS (See Fig. 22)
Remove the klik pin and remove wheel from axle.
6.
7.
REMOVE AUGER BELT from around pulley.
RELIEVETENSIONONTRACTIONDRIVEBELTIDLER
and remove  traction drive  belt from  around pulleys.
IMPORTANT: When installing wheel, be sure to use the in-
nermost hole in axle and the wheel hub hole. To disengage
drive system from the wheels (for pushing or transporting
the snow  thrower), remove klik  pin from  wheel hub and
insert pin into the outermost hole in axle only.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in  idler arm and rotate ratchet clockwise
to relieve tension.
With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
8.
KLIK PIN
OUTER HOLE
9.
Placeaugerbeltaroundandinsidethegrooveofauger
pulley only.
10.
While your  assistant slowly  raises handles  to rejoin
the auger housing and frame assembly, pull up on the
auger belt and  squeeze sides together above  pulley
so belt is fully seated in groove of pulley.
INNER
HOLE
11.
Bring snow  thrower  completely together  and check
carefully for proper routing of belts.  If  auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket  while  bringing snow  thrower together),
separate the snow thrower  and repeat step 10.  Belt
must be  fully seated in  pulley groove when bringing
the snow thrower together.
WHEEL
WHEEL HUB
FIG. 22
16
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2007
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 36 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website