Poulan Pro PP11530ES 415153 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
10.
11. Placeaugerbeltaroundandinsidethegrooveofauger
pulley only.
12.
13.
Install clutch rod in swing plate; secure with hairpin.
be replaced. It is recommended that the belt(s) be replaced
by a qualified service center.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
While your  assistant slowly  raises handles  to rejoin
the auger housing and frame assembly, pull up on the
auger belt and  squeeze sides together above  pulley
so belt is fully seated in groove of pulley.
Bring snow  thrower  completely together  and check
carefully for proper routing of belts.  If  auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket  while  bringing snow  thrower together),
separate the snow thrower  and repeat step 12.  Belt
must be  fully seated in  pulley groove when bringing
the snow thrower together.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Usingother
than OEM belts  can cause personal injury or  damage to
the snow thrower.
WARNING: Belt replacement  requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that an
assistantstandintheoperatingposition
andholdthesnowthrowerhandles.Se-
rious personal injury and/or damage to
theunitcouldoccurifthesnowthrower
should  fall during  the  belt  changing
process.
14.
Install the two (2) hex bolts and tighten securely.
15. INSTALLENGINEPULLEY-Placebeltinpulleygroove
and  slide pulley  on  crankshaft.   Install  flat washer,
lockwasher and bolt and tighten securely (41-47 N-m
torque).  Make sure belt is inside belt keeper.
16.
INSTALL BELT COVER and  two (2) screws. Tighten
securely.
INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
FRAME
ASSEMBLY
AUGER
HOUSING
17.
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
HANDLES
FLAT WASHER
PULLEY
1.
2.
REMOVEGASOLINEFROMFUELTANK-Draingaso-
line from fuel tank into a suitable container, outdoors,
away from fire or flame. Wipe up any spilled gasoline.
REMOVE  DISCHARGE  CHUTE  -  Loosen  locknut
securing chute rotator head to mounting bracket only
enough to allow  chute rotator head to be  raised and
discharge chute to be removed from snow thrower.
LOCKWASHER
BOLT
IDLER ARM
SQUARE
HOLE
AUGER
BELT
3.
4.
REMOVE BELT COVER  - See “TO  REMOVE BELT
COVER” in this section of this manual.
REMOVEENGINEPULLEY-Removebolt,lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
CLUTCHING
IDLER ARM
BRACKET
AUGER
HOUSING
FRAME
AUGER PULLEY
BOLTS
5.
SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
removethetwo(2)boltsholdingtheaugerhousingand
frame together.
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
6.
REMOVEHAIRPINFROMCLUTCHRODandremove
clutch rod from swing plate.  Tip swing plate forward.
REMOVE AUGER BELT from around pulley.
RELIEVETENSIONONTRACTIONDRIVEBELTIDLER
and remove  traction drive  belt from  around pulleys.
FIG. 24
TO REMOVE WHEELS (See Fig. 25)
Remove the klik pin and remove wheel from axle.
7.
8.
IMPORTANT:Wheninstallingwheel,besuretousetheaxle
hole closest to the end of the  shaft – do not use the hole
in the wheel hub (if equipped). Inner hole in axle and hole
in wheel hub  are not used for  your model snow thrower.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in  idler arm and rotate ratchet clockwise
to relieve tension.
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
9.
With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
17
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2007
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website