TO REMOVE WHEELS (See Fig. 26)
Remove the klik pin and remove wheel from axle.
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
•
IMPORTANT: When installing wheel, be sure to use the
axle hole closest to the end of the shaft – do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
holeinwheelhubarenotusedforyourmodelsnowthrower.
ENGINE
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 2,134 meters. If
your engine does not operate properly due to suspected
carburetor problems, take your snow thrower to a qualified
service centre/department.
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY)
OUTER HOLE
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualified service centre/
department, which has the proper equipment and experi-
ence to make any necessary adjustments.
AXLE
WHEEL
WHEEL HUB
FIG. 26
STORAGE
Immediately prepare your snow thrower for storage at the
end of the season or if the unit will not be used for 30 days
or more.
•
•
•
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
WARNING: Never store the snow
throwerwithgasolineinthetankinside
a building where fumes may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gasappliance. Allowtheenginetocool
before storing in any enclosure.
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease, leaves, etc.
Store in a clean, dry area.
ENGINE OIL
Drain oil (with engine warm) and replace with clean en-
gine oil. (See “ENGINE” in the Maintenance section of
this manual).
1.
Clean entire snow thrower (See “CLEANING” in the
Maintenance section of this manual).
CYLINDER
2.
Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
Lubricate as shown in the Maintenance section of this
manual.
Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
1. Remove spark plug.
2.
3.
4.
Pour approximately one ounce (30 ml) of oil through
spark plug hole into cylinder.
Pullrecoilstarterhandleslowlyafewtimestodistribute
oil.
3.
4.
Replace with new spark plug.
OTHER
5.
•
•
•
Remove safety ignition key; store it in a safe place.
Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
ENGINE
FUEL SYSTEM
•
•
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
Coveryoursnowthrowerwithasuitableprotectivecover
thatdoesnotretainmoisture.Donotuseplastic.Plastic
cannotbreathe,whichallowscondensationtoformand
will cause your snow thrower to rust.
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuel hose, or tank during storage. Alcohol blended fuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm.
18
| Categories | Poulan Pro Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Poulan Pro PP13TEPH30 |
| Model Year | 2007 |
| Download File |
|
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)