Poulan Pro PR5524ES 416829 Snow Blower Owners Manual

OPERATION
TO ADJUST SKID PLATES (See Fig. 17)
NOTE: The  wrench provided  in your  parts bag  may be
WARNING:  Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
used to adjust the skid plates.
NOTE: The  wrench provided  in your  parts bag  may be
used to adjust the skid plates.
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
Skid plates are located on each side of the auger housing
ground surface. Adjust skid plates evenly to proper height
and adjust the clearance between the scraper bar and the
for  current surface  conditions.  For  removal of  snow  in
ground surface. Adjust skid plates evenly to proper height
CAUTION:
Alcohol   blended  fuels   (called
gasohol or using ethanol or methanol) can at-
tract moisture which  leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should  be emptied before  storage of
normal conditions, such as a paved driveway or sidewalk,
for  current surface  conditions.  For  removal of  snow  in
place skid  plates in the  highest position (lowest  scraper
normal conditions, such as a paved driveway or sidewalk,
clearance) to give  a 1/8" clearance between the  scraper
place skid  plates in the  highest position (lowest  scraper
bar and the ground.  Use  a middle position if the surface
clearance) to give  a 1/8" clearance between the  scraper
to be cleared is uneven.
bar and the ground.  Use  a middle position if the surface
to be cleared is uneven.
NOTE: It is not recommended to operate the snow thrower
30
days or  longer.   Drain the  gas tank,  start
overgravelorrockysurfaces.Objectssuchasgravel,rocks
NOTE: It is not recommended to operate the snow thrower
the  engine and  let it  run  until the  fuel lines
and carburetor are empty.  Use fresh fuel next
season. SeeStorageInstructionsforadditional
information.  Never  use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
or other debris, can easily be picked up and thrown by the
overgravelorrockysurfaces.Objectssuchasgravel,rocks
impeller, which can cause serious personal injury, property
or other debris, can easily be picked up and thrown by the
damage or damage to the snow thrower.
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
If snow thrower must be operated over gravel surface,
to lowest (highest scraper clearance) position.
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
1.
Shut off engine and wait for all moving parts to stop.
1.
2.
Shut off engine and wait for all moving parts to stop.
Adjust skid plates by  loosening the rear 1/2" hex nut
CHOKE CONTROL
THROTTLE    PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
2.
only,thenmovingskidplatetodesiredposition.Besure
Adjust skidplatesbylooseningthehexnuts,    thenmov-
both plates are adjusted evenly. Tighten securely.
ing skid plate to desired position. Be sure both plates
are adjusted evenly. Tighten securely.
SCRAPER BAR
SAFETY
IGNITION
KEY
HIGH POSITION
(LOW GROUND
CLEARANCE)
AUGER
HOUSING
SCRAPER BAR
SKID PLATE
HEX
NUTS
GASOLINE
FILLER CAP
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 17
FUEL SHUT-
OFF VALVE
The scraper bar is not adjustable, but is reversible.  After
considerable use it may become worn.  When it has worn
almost to  the  edge of  the housing,  it  can be  reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
RECOIL
STARTER BUTTON
STARTER
HANDLE
POWER CORD PLUG
NOTE:  ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
BEFORE STARTING THE ENGINE
FIG. 18
CHECK ENGINE OIL LEVEL (See Fig. 18)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
TO START ENGINE
Be sure fuel shut-off valve is in the OPEN position.
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug  and is
designed to operate on 120 Volt A.C. household current.
1.
2.
Check engine oil with snow thrower on level ground.
Remove oil  fill cap/dipstick  and wipe clean,  reinsert
the dipstick and  screw tight, wait  for a few seconds,
remove and read  oil level. If  necessary, add oil  until
“FULL” mark on dipstick is reached. Do not overfill.
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
Be  sure  your house  is  a  120  Volt A.C.  three-wire
grounded  system.   If  you  are  uncertain,  consult a
licensed electrician.
ADD GASOLINE (See Fig. 18)
WARNING:  Do  not   use  the  electric
starter if your  house is not a 120  Volt
A.C. three-wire grounded system.  Se-
riouspersonalinjuryordamagetoyour
snow thrower could result.
Fill fuel tank to bottom of tank filler neck. Do not over-
fill.  Use fresh, clean,  regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
11
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2007
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website