SERVICE AND ADJUSTMENTS
TO REPLACE BELTS (See Fig. 24)
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
9. With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
The auger and traction drive belts are not adjustable. If
the belts are damaged or begin to slip from wear, they
should be replaced. It is recommended that the belt(s) be
replaced by a service centre/department.
NOTE: It is recommended that both the auger and traction
10. Install clutch rod in swing plate; secure with hairpin.
drive belt be replaced at the same time.
11.
Placeaugerbeltaroundandinsidethegrooveofauger
pulley only.
The V-belts on your snow thrower are of special construc-
tion and should be replaced by original equipment manu-
facturer (OEM) belts available from your nearest service
centre/department. Using other than OEM belts can cause
personal injury or damage to the snow thrower.
12.
While your assistant slowly raises handles to rejoin
the auger housing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
13.
Move idler arm so it does not hit impeller pulley as you
bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket while bringing snow thrower together),
separate the snow thrower and repeat step 12. Belt
must be fully seated in pulley groove when bringing
the snow thrower together.
WARNING: Belt replacement requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that
an assistant stand in the operating
position and hold the snow thrower
handles. Serious personal injury and/
or damage to the unit could occur if
the snow thrower should fall during
the belt changing process.
14.
Install the two (2) hex bolts and tighten securely.
15. INSTALLENGINEPULLEY-Placebeltinpulleygroove
and slide pulley on crankshaft. Install flat washer,
lockwasher and bolt and tighten securely (41-47 N-m
torque). Make sure belt is inside belt keeper.
FRAME
ASSEMBLY
AUGER
HOUSING
16.
INSTALL BELT COVER and two (2) screws. Tighten
securely.
17.
INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
HANDLES
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
1.
2.
REMOVE GASOLINE FROM FUEL TANK - Drain
gasoline from fuel tank into a suitable container, out-
doors, away from fire or flame. Wipe up any spilled
gasoline.
REMOVE DISCHARGE CHUTE - Loosen locknut
securing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
discharge chute to be removed from snow thrower.
FLAT WASHER
PULLEY
LOCKWASHER
BOLT
3.
4.
REMOVE BELT COVER - See “TO REMOVE BELT
COVER” in this section of this manual.
REMOVEENGINEPULLEY-Removebolt,lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two (2) bolts holding the auger housing
and frame together.
IDLER ARM
SQUARE
HOLE
AUGER
BELT
CLUTCHING
IDLER ARM
BRACKET
5.
AUGER
HOUSING
FRAME
AUGER PULLEY
BOLTS
WARNING: As the last bolt is removed,
haveyourassistantcarefullylowerthe
handles down to the ground.
6.
REMOVE HAIRPIN FROM CLUTCH ROD and re-
move clutch rod from swing plate. Tip swing plate
forward.
FIG. 24
7.
8.
REMOVE AUGER BELT from around pulley.
RELIEVE TENSION ON TRACTION DRIVE BELT
IDLER and remove traction drive belt from around
pulleys.
TO REMOVE WHEELS (See Fig. 25)
Remove the klik pin and remove wheel from axle.
•
17
| Categories | Poulan Pro Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Poulan Pro 96192001904 |
| Model Year | 2008 |
| Download File |
|
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)