Poulan Pro 961980022 420925 Snow Blower Owners Manual

OPERATION
ground surface. Adjust skid plates evenly to proper height
BEFORE STARTING THE ENGINE
for  current surface  conditions.  For  removal of  snow  in
normal conditions, such as a paved driveway or sidewalk,
place skid  plates in the  highest position (lowest  scraper
clearance) to give  a 1/8" clearance between the  scraper
bar and the ground.  Use  a middle position if the surface
to be cleared is uneven.
CHECK ENGINE OIL LEVEL (See Fig. 21)
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
1.
2.
Check engine oil with snow thrower on level ground.
Remove oil  fill cap/dipstick  and wipe clean,  reinsert
the dipstick and  screw tight, wait  for a few seconds,
remove and read  oil level. If  necessary, add oil  until
“FULL” mark on dipstick is reached. Do not overfill.
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
ADD GASOLINE (See Fig. 21)
Fill fuel tank to bottom of tank filler neck. Do not over-
fill.  Use fresh, clean,  regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
1.
Shut off engine and wait for all moving parts to stop.
2
.   Adjust skidplatesbylooseningthehexnuts,    thenmov-
ing skid plate to desired position. Be sure both plates
are adjusted evenly. Tighten securely.
WARNING:  Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
HIGH POSITION
(LOW GROUND
CLEARANCE)
CAUTION:
Alcohol   blended  fuels   (called
AUGER
HOUSING
gasohol or using ethanol or methanol) can at-
tract moisture which  leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should  be emptied before  storage of
SCRAPER BAR
HEX
SKID PLATE
NUTS
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 19
30
days or  longer.   Drain the  gas tank,  start
the  engine and  let it  run  until the  fuel lines
and carburetor are empty.  Use fresh fuel next
season. SeeStorageInstructionsforadditional
information.  Never  use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
SCRAPER BAR (See Fig. 19)
The scraper bar is not adjustable, but is reversible.  After
considerable use it may become worn.  When it has worn
almost to  the  edge of  the housing,  it  can be  reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
CHOKE CONTROL
THROTTLE    PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
TO USE DRIFT CUTTERS (See Fig. 20)
Use the drift cutters to cut through deep snowdrifts that are
higher than the front of the snow thrower.
SAFETY
IGNITION
KEY
Loosen  upper adjustment  nut enough  to  allow drift
cutter to be raised to highest position and tighten nut
securely. Repeat for opposite side of snow thrower.
When not  using drift cutters, loosen  adjustment nut,
lower to storage position and tighten nut securely.
AUGER
HOUSING
GASOLINE
FILLER CAP
FUEL SHUT-
OFF VALVE
STORAGE
POSITION
DRIFT
CUTTER
RECOIL
STARTER
HANDLE
STARTER BUTTON
POWER CORD PLUG
ADJUST-
MENT NUT
NOTE:  ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 21
FIG. 20
12
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2008
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 40 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website