Poulan Pro PR8527ES 421028 Snow Blower Owners Manual

SERVICE AND ADJUSTMENTS
11.
Placeaugerbeltaroundandinsidethegrooveofauger
pulley only.
WARNING: Belt replacement  requires
separation of the snow thrower. While
separating the auger housing from the
frame  assembly,  it  is important  that
an  assistant  stand  in  the  operating
position  and  hold the  snow  thrower
handles. Serious personal injury  and/
or damage to the unit could occur if the
snowthrowershouldfallduringthebelt
changing process.
12. While  your assistant  slowly raises  handles to  rejoin
the auger housing and frame assembly, pull up on the
auger belt and  squeeze sides together above  pulley
so belt is fully seated in groove of pulley.
13.
Move idler arm so it does not hit impeller pulley as you
bring  snow thrower  completely  together and  check
carefully for proper routing of belts.  If  auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket  while  bringing snow  thrower together),
separate the snow thrower  and repeat step 12.  Belt
must be  fully seated in  pulley groove when bringing
the snow thrower together.
FRAME
ASSEMBLY
AUGER
HOUSING
14.
15.
Install the two (2) hex bolts and tighten securely.
INSTALLENGINEPULLEY-Placebeltinpulleygroove
and  slide pulley  on  crankshaft.   Install  flat washer,
lockwasher and bolt and tighten securely (41-47 N-m
torque).  Make sure belt is inside belt keeper.
16.
17.
INSTALL BELT COVER and  two (2) screws. Tighten
securely.
INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
HANDLES
1.
2.
REMOVEGASOLINEFROMFUELTANK-Draingaso-
line from fuel tank into a suitable container, outdoors,
away from fire or flame. Wipe up any spilled gasoline.
REMOVE  DISCHARGE  CHUTE  -  Loosen  locknut
securing chute rotator head to mounting bracket only
enough to allow  chute rotator head to be  raised and
discharge chute to be removed from snow thrower.
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
3.
4.
REMOVE BELT COVER  - See “TO  REMOVE BELT
COVER” in this section of this manual.
REMOVEENGINEPULLEY-Removebolt,lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
removethetwo(2)boltsholdingtheaugerhousingand
frame together.
FLAT WASHER
PULLEY
LOCKWASHER
BOLT
5.
IDLER ARM
SQUARE
HOLE
AUGER
BELT
CLUTCHING
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
IDLER ARM
BRACKET
AUGER
HOUSING
FRAME
AUGER PULLEY
6.
REMOVEHAIRPINFROMCLUTCHRODandremove
clutch rod from swing plate.  Tip swing plate forward.
BOLTS
7.
8.
REMOVE AUGER BELT from around pulley.
RELIEVE  TENSION  ON  TRACTION  DRIVE BELT
IDLER  and remove  traction  drive belt  from  around
pulleys.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in  idler arm and rotate ratchet clockwise
to relieve tension.
FIG. 22
9.
With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
10.
Install clutch rod in swing plate; secure with hairpin.
16
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2008
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 40 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website